background image

Installation 

8

3A3101F

Installation

Grounding

Pump: 

ground through electrically conductive air and 

fluid lines.

Air and fluid lines:

 use only electrically conductive 

lines. 

Air compressor:

 follow manufacturer’s recommenda-

tions.

Fluid supply container:

 follow local code.

Required Accessories

Install the following required accessories in the order 
shown in F

IG

. 2, using adapters as necessary. See 

Kits 

and Accessories 

starting on page 42.

Air Line

Bleed-type master air valve (D):

 required in your 

system to relieve air trapped between it and the air 
motor when the valve is closed.

Be sure the valve is easily accessible from the 
pump and located downstream from the air reg-
ulator.

Pump air regulator (E):

 to control pump speed and 

outlet pressure. Locate it close to the pump.

Air line filter (C):

 removes harmful dirt and mois-

ture from compressed air supply.

Second bleed-type air valve (air shutoff valve) 
(B):

 isolates air line accessories for servicing. 

Locate upstream from all other air line accessories.

Fluid Line

Fluid filter (Y-Strainer) (included in G):

 with a 60 

mesh (250 micron) stainless steel element to filter 
particles from the fluid before in reaches the pump. 

Fluid shutoff valve (H):

 shuts off fluid flow.

Pressure relief valve (J):

 overload protection.

Flush Before Using Equipment

The equipment was tested with lightweight oil, which is 
left in the fluid passages to protect parts. To avoid con-
taminating your fluid with oil, flush the equipment with a 
compatible solvent before using the equipment. See 

Flush the Equipment

, page 17.

The equipment must be grounded to reduce the risk 
of static sparking. Static sparking can cause fumes to 
ignite or explode. Grounding provides an escape wire 
for the electric current.

Summary of Contents for Python A25030

























































Reviews: