background image

Instructions

3A1495C

11

Throat and Piston Seal Replacement Kit - 
24H854 (

Fig. 25

)

Replacement parts for o-ring (5) installed on air piston 
(15), o-rings (6 and 12) installed in bottom cover (14), 
o-ring (7), u-cup seal (11) and gasket (30) installed on 
flange (22), pin (8) used to reassemble rod sections, 
and gasket (18) used later in reassembly of the air valve 
(40). A replacement part for the retainer nut (37) is also 
included in this kit.

1. Disassemble the pump following Disassembly 

Steps 1-3 (page 3), Steps 9-12 (page 5) and 15-21 
(pages 5-6). 

2. Use a pick to remove the o-ring (5) installed around 

the circumference of the air piston (15) (Fig. 26). 
Grease the new o-ring included in the kit and install 
it around the air piston.

3. Use a pick to remove o-ring (7) and gasket (30) from 

inside flange (22) (Fig. 27). Grease the o-ring and 
replace the o-ring and gasket in flange.

Ref. Description

Qty

.

5

O-RING, air piston

1

6

O-RING

1

7

O-RING

1

8

PIN, slotted, straight

3

11

SEAL, u-cup

1

12

O-RING

3

18

GASKET, cover, small

2

30

GASKET

1

37

NUT, retainer

1

Fig. 25

7

6

18

5

12

8

11

30

37

Fig. 26

Fig. 27

5

15

7

22

30

22

Summary of Contents for LD 24H854

















Reviews: