background image

3A5294B

EN

Instructions

LazerGuide 1700, LazerGuide 2000 
and LazerGuide 3000 Kits

For installation of the LazerGuide 1700, 2000 and/or 3000 Kits on LineLazer

, RoadPak

Sure 

Stripe 3350SP, and Brite Striper 3500SP airless line striping systems. 

For professional use only.

Important Safety Instructions

Read all warnings and instructions in this manual and in related manuals.
Be familiar with the controls and the proper usage of the equipment. 
Save these instructions.

Related Manuals:

3A3388

LLV 3900/5900 Operation

3A3426

LLV 200HS Operation

3A3393

LLV 250SPS and 250DC Operation

3A4603

LL ES1000 Operation, Repair, Parts

3A4637

SureStripe 3350 Operation, Repair, Parts

3A4555

BriteStriper 3500 Operation

3A5384

RoadPak Operation

 -------

Laser Manufacturer’s Manual

LASER LIGHT HAZARD: AVOID DIRECT EYE 
CONTACT

Eye exposure to Class IIIa/3R levels of laser light can 
potentially present an eye (retinal) injury hazard, 
including spot blindness or other retinal injury. Refer 
to laser warnings in laser manufacturer’s manual.

 

LazerGuide 2000

LazerGuide 3000

LazerGuide 1700

Summary of Contents for LazerGuide 3000

























Reviews: