background image

Pressure Relief Procedure

3A0096B

13

Pressure Relief 
Procedure

1.

Lock the dispense valve trigger.

2.

Shut off the power to the pump:

In an air-powered system, close the air regula-
tor (H) and the bleed-type master air valve (J).

In a hydraulic-powered system, close the 
hydraulic supply line shutoff valve (E) first, then 
the return line shutoff valve (S).

3.

Unlock the valve trigger.

4.

Hold a metal part of the valve firmly to the side of a 
grounded metal pail, and trigger the valve to relieve 
pressure.

5.

Lock the valve trigger.

6.

Open the fluid line drain valve and the pump bleed 
valve (N). Have a container ready to catch the drain-
age.

7.

Leave the pump bleed valve open until ready to dis-
pense again.

If you suspect that the nozzle or hose is completely 
clogged, or that pressure has not been fully relieved 
after following the steps above, very slowly loosen the 
retaining nut, nozzle, or hose end coupling and relieve 
pressure gradually, then loosen completely. Now clear 
the nozzle or hose.

Prime/Flush

NOTE:

 The pump is tested with lightweight oil, which is 

left in to protect the pump parts. If the fluid you are using 
may be contaminated by the oil, flush it out with a com-
patible solvent before using the pump.

Flush with a fluid that is compatible with the fluid you are 
pumping and with the wetted parts in your system. 
Check with your fluid manufacturer or supplier for rec-
ommended flushing fluids and flushing frequency. 
Always flush the pump before fluid dries on the displace-
ment rod.

1.

Follow 

Pressure Relief Procedure

 on page 13.

2.

Supply solvent to the pump.

3.

Hold a metal part of the valve firmly to the side of a 
grounded metal pail.

4.

Start the pump. Always use the lowest possible fluid 
pressure when flushing.

5.

Trigger the valve.

6.

Flush the system until clear solvent flows from the 
valve.

7.

Relieve the pressure.

NOTICE

Never leave water or water-based fluid in a carbon 
steel pump overnight. If you are pumping a 
water-based fluid, flush with water first. Then flush 
with a rust inhibitor, such as mineral spirits. Relieve 
pressure, but leave rust inhibitor in pump to protect 
parts from corrosion.

Summary of Contents for L200CM





















Reviews: