background image

ACCESSORIES 

PUMP RUNAWAY VALVE 

psi 

MAXIMUM WORKING PRESSURE 

Shut off air supply to the pump if the pump accelerates 

beyond the 

setting due to an empty supply 

container,  interrupted fluid supply to the pump,  or 

ex- 

cessive cavitation. 

HOW 

TO 

ORDER  REPLACEMENT PARTS 

To 

be sure 

you 

receive the correct replacement parts, 

kit or  accessories, always give all of the information 

requested 

in the chart below. 

2. 

Check the parts list to identify the correct 

part 

number; 

do not 

use the ref.  n a  when ordering. 

3.  Order 

all parts from your nearest 

Gram 

distributor. 

digit 

PART 

NUMBER 

PART DESCRIPTION 

GROUNDED NYLON FLUID HOSE 

psi 

bar) MAXIMUM WORKING PRESSURE 

Urethane Cover 

114" 

114" 

114 

114 

swivel 

114 

swivel 

318 

114 

swivel 

psi 

(350 

barl MAXIMUM  WORKING PRESSURE 

HYDRA-SPRAY GUN 218-132 

With 

0.09 

in. 

(2.29 

orifice 

HYDRA-SPRAY GUNS 

psi 

barl MAXIMUM WORKING PRESSURE 

with 0.037  in. 

orifice 

208-663 

with 

0.09 

in. 

(2.29 

orifice 

with 

0.09 

in. 

(2.29 

orifice, 

finger trigger 

SERVICE INFORMATION 

Listed 

below by the assembly changed are 

OLD, 

NEW, 

ADDED 

and 

DELETED 

parts 

ASSEMBLY PART 

REF  PART 

CHANGED  STATUS  NO.  NO. 

NAME 

ADDED 

123 

V-Packing 

DELETED 

123 

V-Packing 

ADDED 

124 

V-Packing 

.. 

DELETED 

124  164-913  V-Packing 

parts ere not interchangeable. 

INTERCHANGEABILITY NOTE: ADDED 

and 

DELETED 

307-619 

13 

Summary of Contents for HYDRA-SPRAY 218-058 A

















Reviews: