Graco Husky 1040 Instructions-Parts List Manual Download Page 3

Page: 3 / 36

308443

Warnings

Symbols

Warning Symbol

WARNING

Caution Symbol

This symbol alerts you to the possibility of serious injury
or death if you do not follow the instructions.

CAUTION

This symbol alerts you to the possibility of damage to or
destruction of equipment if you do not follow the
instructions.

INSTRUCTIONS

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.

•

This equipment is for professional use only.

•

Read all instruction manuals, tags, and labels before operating the equipment.

•

Use the equipment only for its intended purpose. If you are not sure, call your Graco distributor.

•

Do not alter or modify this equipment. Use only genuine Graco parts and accessories.

•

Check equipment daily. Repair or replace worn or damaged parts immediately.

•

Do not exceed the maximum working pressure of the lowest rated component in your system. This
equipment has a

120 psi (0.8 MPa, 8 bar) maximum working pressure at 120 psi (0.8 MPa,

8 bar) maximum incoming air pressure.

•

Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the

Technical Data

section of all equipment manuals. Read the fluid and solvent manufacturer’s

warnings.

•

Do not use hoses to pull equipment.

•

Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not expose
Graco hoses to temperatures above 82 °C (180 °F) or below –40 °C (–40 °F).

•

Do not lift pressurized equipment.

•

Comply with all applicable local, state, and national fire, electrical, and safety regulations.

Summary of Contents for Husky 1040





































Search results

Summary of Contents for Husky 1040

Reviews:

Related manuals for Husky 1040

Brands by name

Popular brands

Graco Husky 1040, Instructions-Parts List Manual

Search results

Summary of Contents for Husky 1040

Reviews:

Related manuals for Husky 1040

Brands by name

Popular brands