background image

Instructions – Parts List

GRACO INC.ąP.O. BOX 1441ąMINNEAPOLIS, MNą55440-1441

Copyright 1982, Graco Inc. is registered to I.S. EN ISO 9001

Foam-Cat

r

 Heated Hose

3000 psi (21 MPa, 207 bar) Maximum Working Pressure

Model 218613, Series B

50 foot (15.2 m) Hose, 3/8 in. ID

Model 218614, Series B

15 foot (4.6 m) Whip Hose, 1/4 in. ID

The heated hose maintains proper fluid temperature between the heater and gun
during spraying operations, and it raises the temperature of fluid left in the hose
when the heater is turned on after a shutdown period.

The Series B Heated Hoses include a 75

_

C (167

_

F) high limit thermostat. This

limits the maximum temperature to less than the 82

_

C (180

_

F) rating of the hoses,

allowing use at a full 3000 psi (21 MPa, 207 bar) pressure rating.

U.S. Patent No. 4,725,713
United Kingdom Patent No. 2,138,601
Brevete 1986 Canada

307544M

Read warnings and instructions.

See page 2 for table of contents.

WARNING

FIRE, EXPLOSION, AND ELECTRIC SHOCK HAZARD

The operating and safety features of these hoses are
designed for use 

only

 with the Graco Foam-Cat

r

 Heater and

Heater Hose Controls: Models 235259, 235839, 235260, and
235840. To reduce the risk of serious injury, never connect
these hoses to any other device.

CSA certified for use with Models
235259, Series B, 235839, Series B,
235260, Series B, and 235840, Series B
Foam-Cat Heaters.

Model 218613

Parts

Summary of Contents for Foam-Cat 218613













Reviews: