background image

Repair 

8

312375J

12. Torque cartridge (3) to specified torque listed in the 

following table.

13. Slide packing nut/wet cup (9) over displacement rod 

(1) and torque to specified torque listed in the follow-
ing table.

14. Fill wet cup (9) 1/3 full of TSL or compatible solvent.

Disassembly

When disassembling displacement pump, lay out all 
removed parts in sequence to ease reassembly. Clean 
all parts with a compatible solvent and inspect them for 
wear or damage.

1.

Relieve pressure. See your Check-Mate Pump 
Packages manual 312376 for instructions.

2.

Disconnect displacement pump from air motor as 
illustrated in your Check-Mate Pump Packages 
manual 312376.

3.

Place displacement pump in a vise, with jaws on 
outlet housing (2). 

4.

Use packing nut wrench (supplied) to loosen and 
remove packing nut/enclosed wet cup (9).

5.

On displacement pumps with enclosed wet cups (9), 
use an M4 hex wrench to remove the three screws 
(14) from wet cup cover (10) and remove cover. 
Drain and clean out the wet cup (9). See F

IG

. 5.

6.

On displacement pumps with enclosed wet cups (9), 
use o-ring pick to remove o-ring (11), and a flat 
head screwdriver to remove snap ring (61), wiper 
(15), and seal (16).

Displacement 
Pump

Torque

60cc and 100cc

90-130 ft-lbs (122-173 N•m)

200cc and 250cc

130-190 ft-lbs (176-258 N•m)

500cc

149-261 ft-lbs (203-355 N•m)

Displacement 
Pump

Torque

60cc and 100cc

28-44 ft-lbs (38-59 N•m)

200cc and 250cc

95-115 ft-lbs (128-155 N•m)

500cc

95-115 ft-lbs (128-155 N•m)

F

IG

. 4

The snap ring (61) is applicable only to 60cc and 
100cc displacement pumps.

F

IG

. 5

9

ti10623a

ti10561a

10

61

11

16

14

9

15

Summary of Contents for Check-Mate 312375J













































Reviews: