background image

 

4

312290A

Project Painter 5: 261800

Disassembly

1

Unplug electrical cord, and relieve pressure.

2

Remove suction tube, drain line and coupled hose.

3

Fig. 4. Cut 

AllControl

 labels at two places where upper 

and lower housings mate (A).

4

Remove four screws (B) and base tube

5

Fig. 5. Stand sprayer in upright position. Remove four front 
cover screws (C). Put 

AllControl

 knob in 

ROLL

 position.

6

Fig. 5. Remove front cover subassembly from base and 
place face down on bench.

7

Fig. 4. Disconnect pressure control connector (D) from 
control board. 

8

Remove six screws (E) from pump housing.

9

Fig. 6. Turn sprayer with drive housing face up. Wiggle 
drive housing and remove.

10 Remove two screws (F) from pressure control mounting 

plate.

11 Remove pressure control assembly from pump housing.

F

IG

. 4

Assembly

1

Grease o-ring on pressure control assembly. Push 
pressure control down into machined slots in pump 
housing. Secure with two screws (F). Torque to 40 ±5 in-lb.

2

Align gears in drive housing with pump housing and 
assemble housings. Keep drive housing and pump 
housing together and turn sprayer with drive housing face 
down,

3

Install pump housing to drive housing with six screws (E). 
Torque 29 ±3 in-lb.

4

Put 

AllControl

 knob in 

ROLL

 position.

5

Plug 

AllControl

 harness connector (D) into control board. 

Align electrical cord strain relief in drive housing.

6

Install sprayer in base with four screws (C).
Torque 29 ±3 in-lb.

7

Install base tube on frame with four screws (B). 
Torque 29 ±3 in-lb.

8

Remove old labels and install new labels (A).

9

Install coupled hose, drain line and suction tube.

F

IG

. 5

CAUTION

 Be careful not to damage wires on disassembly/assembly.

PP5 WIRING DIAGRAM

ALL CONTROL

10A FUSE

ti10241a

ti10288a

A

B

D

C

ti10289a

Summary of Contents for AllControl 288711







Reviews: