Graco 2730B Instructions Manual Download Page 3

Page: 3 / 32

Equipment Misuse Hazard:

Misuse of pressure

washer or accessories can cause the equipment to
rupture or malfunction and result in serious injury.

Do not alter or modify any part or factory–set ting

Check equipment daily. Repair or replace worn

or damaged parts immediately.

Do not exceed maximum working pressure (MWPR) of the lowest–

rated system component

Use fluids and solvents that are compatible with the equipment

wetted parts. See Specifications on page for this information.

Wear hearing protection when operating this equipment.

Do not “blow back” fluid; this is not an air spray system

Pressure Relief

before cleaning, checking or servicing the

equipment.

Injection Hazard:

Spray from gun, leaks or

ruptured components can inject fluid into your body

and cause serious injury. Fluid splashed in eyes or

on skin can also cause serious injury.

Fluid injected into the skin might look like just a

cut, but it is a serious injury.

Get emergency

medical attention.

Do not point the gun at anyone or any part of the

body.

Do not stop or deflect leaks with hand, body, glove, or rag.

Do not put your hand or fingers over the spray tip.

TIghten fluid connections before you start this equipment.

Engage the gun safety whenever you stop spraying.

Pressure Relief Procedure

on page 7 if the spray tip

clogs and before you clean, check or service this equipment.

Repair or replace worn or damaged parts immediately.

Check hoses, tubes, and couplings daily. Do not repair high–pres-

sure couplings. Replace entire hose. Fluid hoses must have
spring guards on both ends to prevent kinks and rupture.

TOXIC FLUID HAZARD:

Hazardous fluid or toxi

fumes can cause serious injury or death if
splashed in eyes or on skin, inhaled, or
swallowed.

Know specific hazards of fluids you are

using and take protective measures as
recommended by the fluid and solvent
manufacturer.

Fuel Hazard:

The fuel used in this pressure

washer is combustible. When spilled on a hot
surface it can ignite and cause a fire.
Do not fill fuel tank while engine is running or hot.

Exhaust Hazard:

The exhaust contains poisonous

carbon monoxide, which is colorless and odorless.
Do not operate this equipment in a closed building.

309286

Summary of Contents for 2730B

































Search results

Summary of Contents for 2730B

Reviews:

Graco 2730B, Instructions Manual, Page: 3 / 32

Search results

Summary of Contents for 2730B

Reviews: