Graco 262893 Instructions - Parts Manual Download | Manualshive

Page: 1 / 22

background image

Instructions - Parts

XM PFP Mix Manifold

Dual flush, center inject manifold with heated water circulating base for mixing
intumescent epoxies with the XM PFP system. For professional use only.

Part No. 262893

6000 psi (41 MPa, 414 bar) Maximum Working Pressure for A and B materials
4500 psi (31 MPa, 310 bar) Maximum Working Pressure for flushing fluid
100 psi (0.7 MPa, 7 bar) Maximum Working Pressure for heating fluid
180°F (82°C) Maximum Fluid Temperature

Important Safety Instructions

Read all warnings and instructions in this manual
and XM PFP Operation manual. Save all instruc-
tions.

ti20088a

3A2988C

EN

II 2 G Ex h T5 Gb

1
2
3
...
»

Summary of Contents for 262893























Reviews:

No comments

Related manuals for 262893

MicroVersaTrip Plus

Brand: GE Pages: 20

MicroVersaTrip Plus

Brand: GE Pages: 2

Brand: GE Pages: 252

Brand: Balanced Body Pages: 12

Brand: Eagle Pro Pages: 6

Brand: GE Pages: 10

ImageQuant LAS 4000

Brand: GE Pages: 86

Brand: GE Pages: 160

Brand: GE Pages: 134

Brand: OfiTE Pages: 21

Brand: Earthlite Pages: 4

Brand: YATEK Pages: 78

Brand: Yamaha Pages: 50

Brand: A&D Pages: 30

Brand: Abbott Pages: 2

FreeStyle Libre

Brand: Abbott Pages: 3

Brand: abc Pages: 8

Brand: Jackco Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands