Graco 25U546 Manual Download Page 28

Page: 28 / 48

Cleaning and Flushing Fluid Compatibility

3A9031A

Cleaning and Flushing Fluid Compatibility

When flushing with flammable materials, always follow

Grounding Instructions

, page 9.

If you’re going to:

Flush with:

Prime with:

Clean with:

Store with:

Spray with new striper or

striper that has been

stored

Compatible fluid such

as water or mineral

spirits

Compatible paint,

such as water-base or

oil-base

Compatible

fluid such as

water or

mineral spirits

Mineral spirits

Spray water-base paint Warm, soapy water,

then clean water

Water-base paint

Warm, soapy

water, then

clean water

Mineral spirits

Spray oil-base paint

Mineral spirits

Oil-base paint

Mineral spirits Mineral spirits

Change water-base to

oil-base paint

Warm, soapy water,

then clean water

Mineral spirits

Mineral spirits Mineral spirits

Change oil-base to

water-base paint

Mineral spirits, soapy

water, then clean water

Water-base paint

Warm, soapy

water, then

clean water

Mineral spirits

Change colors, same

base

Compatible fluid such

as water or mineral

spirits

Summary of Contents for 25U546

















































Search results

Summary of Contents for 25U546

Reviews:

Related manuals for 25U546

Brands by name

Popular brands

Graco 25U546, Manual

Search results

Summary of Contents for 25U546

Reviews:

Related manuals for 25U546

Brands by name

Popular brands