background image

Installation 

6

3A8109A

Installation

Grounding

 

Pump:

 grounded through 

Motor Electrical Connec-

tions

 on page 9.

Fluid lines:

 use only electrically conductive lines.

Fluid supply container:

 follow local codes and regula-

tions.

Accessories

Install the following required accessories in the order 
shown in 

Typical Installation

, page 7, using adapters 

as necessary. These required accessories must be sup-
plied and installed by the customer before use.

Fluid Filter (Y-Strainer) (included in K):

 with a 60 

mesh (250 micron) stainless steel element to filter 
particles from the fluid before it reaches the pump. 

Fluid Shutoff Valves (L):

 shuts off fluid flow.

Pressure Relief Valve (D):

 overpressure protec-

tion.

Flush Before Using Equipment

The equipment was tested with lightweight oil, which is 
left in the fluid passages to protect parts. To avoid con-
taminating your fluid with oil, flush the equipment with a 
compatible solvent before using the equipment. See 

Flush the Equipment

, page 10.

The equipment must be grounded to reduce the risk 
of static sparking and electric shock. Electric or static 
sparking can cause fumes to ignite or explode. 
Improper grounding can cause electric shock. 
Grounding provides an escape wire for the electric 
current.

Summary of Contents for 25T650





















Reviews: