Graco 25T461 Installation, Operation And Service Download

Page: 8 / 12

Service

3A8551B

Service

After the TLM has been installed, the only additional

maintenance or service necessary is changing the

batteries.

Replace Batteries

NOTE: After battery placement, activate the TLM with a

magnet (see

Activation

, page 2), to synchronize the

TLM internal clock to maintain scheduled TLM

readings.

1. Remove the TLM from the tank by unscrewing it

from the opening.

2. Remove the four (4) screws that keep the case

together (F

. 6).

3. Verify that the device is right side up before opening

to prevent the batteries from falling out (F

. 7).

4. Replace the four (4) C-cell Alkaline batteries

. 8).

WARNING

Fire and Explosion Hazard

Sparking can occur when changing batteries. Only

replace the batteries in a non-hazardous location

away from flammable fluids and fumes.

. 6

. 7

. 8

Bottom

Top

Negative (-)

Positive (+)

Summary of Contents for 25T461













Search results

Summary of Contents for 25T461

Reviews:

Related manuals for 25T461

Brands by name

Popular brands

Graco 25T461, Installation, Operation And Service

Search results

Summary of Contents for 25T461

Reviews:

Related manuals for 25T461

Brands by name

Popular brands