Graco 25M841 1 HP Operation And Parts Download Page 4

Warnings 

4

3A5575D

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this 
equipment. The exclamation point symbol alerts you to a general warning and the hazard symbols 
refer to procedure-specific risks. When these symbols appear in the body of this manual or on 
warning labels, refer back to these Warnings. Product-specific hazard symbols and warnings not 
covered in this section may appear throughout the body of this manual where applicable.

WARNING

DUST AND DEBRIS HAZARD

Grinding concrete and other surfaces with this equipment can create dust that contains hazardous 
substances. Grinding can also create flying debris.
To reduce the risk of serious injury:

Control the dust to meet all applicable workplace regulations.

Wear protective eye wear and a properly fit-tested and government approved respirator suitable for 
the dust conditions.

Use equipment only in a well-ventilated area.

Grinding equipment must be used only by trained personnel who understand the applicable 
workplace regulations.

ROTATING PARTS HAZARD

Rotating parts can cut or amputate fingers and other body parts.

Keep clear of rotating parts.

Do not operate equipment with protective guards or covers removed.

Before checking, moving, or servicing equipment, disable power supply.

BURN HAZARD

Equipment surfaces that are heated can become very hot during operation. To avoid severe burns, do 
not touch hot equipment. Wait until equipment has cooled completely.

EQUIPMENT MISUSE HAZARD 

Misuse can cause death or serious injury.

Do not operate the unit when fatigued or under the influence of drugs or alcohol.

Do not leave the work area while equipment is energized. Turn off all equipment when equipment 
is not in use.

Check equipment daily. Repair or replace worn or damaged parts immediately with genuine 
manufacturer’s replacement parts only.

Do not alter or modify equipment.

Use equipment only for its intended purpose. Call your distributor for information.

Keep children and animals away from work area.

Comply with all applicable safety regulations.

Maintain a safe operating distance from other people in the work area.

Avoid any pipes, columns, openings, or any other objects protruding from work surface.

PERSONAL PROTECTIVE EQUIPMENT

You must wear appropriate protective equipment when operating, servicing, or when in the operating 
area of the equipment to help protect you from serious injury, including eye injury, inhalation of dust or 
chemicals, burns, and hearing loss. This equipment includes but is not limited to:

Protective eye wear.

Protective shoes.

Gloves.

Hearing protection.

Properly fit-tested and government approved respirator suitable for the dust conditions.

Summary of Contents for 25M841 1 HP















Reviews: