background image

 

5

MISCELLANEOUS SAFETY PRECAUTIONS

Never allow children or adolescents to operate this unit.

Read and follow all handling, operations, maintenance and safety instructions listed in this manual and the 

engine operator’s manual that accompanies this unit, and provide such information to anyone who will be 

operating this unit.

In freezing temperatures, the unit must always be warm enough to ensure there is no ice formation in the 

pump.  Do not start this unit if it has been transported in an open or under heated vehicle without first al

-

lowing the pump to thaw.

When connecting the water inlet to the water supply mains, local regulations of your water company must 
be observed.  In some areas the unit must not be connected directly to the public drinking water supply.  
This is to ensure that there is no feedback of the detergents into the water supply.  (Direct connection is 

permitted if a back flow preventer is installed.)

Do not allow any part of your body or the high pressure hose to make contact with the muffler.  Avoid 

dragging the hose over an abrasive surface such as cement.  This causes wear and eventual rupturing.

High pressure hoses should be inspected daily for signs of wear.  If evidence of failure exists, promptly re-

place all suspect hoses to prevent the possibility of injury from the high pressure spray.  If a hose or fitting 

is leaking , never place your hand directly on the leak.

Do not operate the unit without all protective covers in place.

Never run the unit with the governor disconnected or operate at excessive speeds.

To reduce the risk of injury, maintain a safe distance for persons while operating this unit.  Close supervi-
sion is necessary when operating the unit near children.

Do not leave pressurized unit unattended.  Shut off the unit and release trapped pressure before leaving.

Do not move the unit by pulling on the hose.

ADJUSTMENT PRECAUTIONS

• 

Never alter or modify the equipment, be sure any accessory items and system components being used 
will withstand the pressure developed.  Use only genuine parts for repair of your pressure washer.  Fail-
ure to do so can cause hazardous operating conditions and will void warranty.

•  Never make adjustments to the machinery while it is connected to the engine without first removing the 

ignition cable from spark plug.  Turning the machinery over by hand during adjustment or cleaning might 
start the engine and machinery with it, causing serious injury to the operator.

• 

Know how to stop the pressure washer and bleed pressures quickly.  Be thoroughly familiar with con-
trols.

• 

Before servicing the unit;  turn the unit off, relieve the water pressure, and allow the unit to cool down.  

Do not make repairs while unit is running.  Service in a clean, dry, flat area.  Block the wheels to prevent 

the unit from moving.

•  Follow the maintenance instructions specified in this manual.

 PERSONAL PROTECTIVE EQUIPMENT

You must wear appropriate protective equipment when operating, servicing, or when in the operating area 
of the equipment to help protect you from serious injury, including eye injury, hearing loss, inhalation of 

toxic fumes, and burns. This equipment includes but is not limited to:

• Protective eyewear, and hearing protection.

• Respirators, protective clothing, and gloves as recommended by the detergent manufacturer.

 

WARNING

Summary of Contents for 2525DD











































Reviews: