background image

34 

 

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name 
to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With 
the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve 
months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This 

warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written 

recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or 
wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, neg-
ligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunc-
tion, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment 
or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of 
structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized 

Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace 

free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. 
If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a 
reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, IN-
CLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PAR-
TICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer 
agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost 

sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for 
breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND 
FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR 
COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco 
(such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will 
provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco sup-
plying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, 
whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

For Graco Canada Customers

The Parties acknowledge that they have required that the present document, as well as all documents, notices and 
legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn 
up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, 
ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, 
directement ou indirectement, avec les procédures concernées.

Graco Information

TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor.

All written and visual data contained in this document reflects the latest product information available at the time of 

publication.

Graco reserves the right to make changes at any time without notice.

MM 3A0465B

Graco Headquarters:

 Minneapolis

International Offices:

 Belgium, China, Japan, Korea

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441

www.graco.com

Written in USA

Summary of Contents for 2525



































Reviews: