Graco 248862 Repair Parts List Manual Download Page 35

Page: 35 / 36

311020

Technical Data

Honda GX120 Engine

Power Rating @ 3600 rpm

ANSI

4.0 Horsepower

. . . . . . . . . . . . . . . . . . . . . . .

DIN 6270B/DIN 6271

2.1 Kw -- 2.8 Ps

. . . . . . . . . . . . . . . . . . . . . .

2.6 Kw -- 3.6 Ps

. . . . . . . . . . . . . . . . . . . . . .

Honda GX160 Engine

Power Rating @ 3600 rpm

ANSI

5.5 Horsepower

. . . . . . . . . . . . . . . . . . . . . . .

DIN 6270B/DIN 6271

2.9 Kw -- 4.0 Ps

. . . . . . . . . . . . . . . . . . . . . .

3.6 Kw -- 4.9 Ps

. . . . . . . . . . . . . . . . . . . . . .

Maximum working pressure

3300 psi

. . . . . . . . . . . . . . .

(228 bar, 22.8 MPa

)

Noise Level

Sound power

105 dBa

. . . . . . . . . . . . . . . . . . . . . . . . .

per ISO 3744

Sound pressure

96 dBa

. . . . . . . . . . . . . . . . . . . . . . . .

measured at 3.1 feet (1 m)

*Vibration Level

LineLazer lV 3900/R300

Left hand

1.81 m/sec

. . . . . . . . . . . . . . . . . . . . . . . .

Right hand

1.45 m/sec

. . . . . . . . . . . . . . . . . . . . . . . .

LineLazer lV 5900

Left hand

2.05 m/sec

. . . . . . . . . . . . . . . . . . . . . . . .

Right hand

1.70 m/sec

. . . . . . . . . . . . . . . . . . . . . . . .

* Vibration measured per ISO 5349 based on 8 hour daily

exposure

Maximum delivery

LineLazer IV 3900/R300

1.15 gpm (4.4 liter/min)

. .

LineLazer IV 5900

1.5 gpm (5.7 liter/min)

. . . . . . . . .

Maximum tip size

LineLazer IV 3900/R300

1 gun with 0. 034 in. tip

. .

2 guns with 0.024 in. tip

LineLazer IV 5900

1 gun with 0. 041 in. tip

. . . . . . .

2 guns with 0.028 in. tip

Inlet paint strainer

16 mesh (1190 micron)

. . . . . . . . . . .

stainless steel screen, reusable

Outlet paint filter

60 mesh (250 micron)

. . . . . . . . . . . . .

stainless steel screen, reusable

Pump inlet size

3/4 in. npt (m)

. . . . . . . . . . . . . . . . . . . . . .

Fluid outlet size

1/4 npsm from fluid filter

. . . . . . . . . . . .

Wetted parts

nickel-plated carbon steel,

. . . . . . . . . . . . .

PTFE, Nylon, polyurethane, UHMW polyethylene,

fluoroelastomer, acetal, leather, tungsten carbide,

stainless steel, chrome plating

Dimensions

LineLazer IV 3900/R300

Model 248862, 249008, 24M605, 24M607 Striper

Weight (dry, without packaging)

212 lb (96 kg)

. . . . . . .

Height

40 in. (101.6 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . .

Length

65 in. (165.1 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . .

Width

32 in. (81.3 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 248863, 249009 Striper with 2nd Gun Kit

Weight (dry, without packaging)

222 lb (101 kg)

. . . . . .

Height

40 in. (101.6 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . .

Length

65 in. (165.1 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . .

Width

32 in. (81.3 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 248864 Striper with Bead

Weight (dry, without packaging)

212 lb (96 kg)

. . . . . . .

Height

40 in. (101.6 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . .

Length

65 in. (165.1 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . .

Width

32 in. (81.3 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 248865 Striper 2nd Gun Kit with Bead

Weight (dry, without packaging)

222 lb (101 kg)

. . . . . .

Height

40 in. (101.6 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . .

Length

65 in. (165.1 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . .

Width

32 in. (81.3 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

LineLazer IV 5900

Model 248866, 249010 Striper

Weight (dry, without packaging)

232 lb (105 kg)

. . . . . .

Height

40 in. (101.6 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . .

Length

65 in. (165.1 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . .

Width

32 in. (81.3 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 248867, 249011 Striper with 2nd Gun Kit

Weight (dry, without packaging)

242 lb (110 kg)

. . . . . .

Height

40 in. (101.6 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . .

Length

65 in. (165.1 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . .

Width

32 in. (81.3 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 248868 Striper with Bead

Weight (dry, without packaging)

232 lb (105 kg)

. . . . . .

Height

40 in. (101.6 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . .

Length

65 in. (165.1 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . .

Width

32 in. (81.3 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model 248869 Striper 2nd Gun Kit with Bead

Weight (dry, without packaging)

242 lb (110 kg)

. . . . . .

Height

40 in. (101.6 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . .

Length

65 in. (165.1 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . .

Width

32 in. (81.3 cm)

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Summary of Contents for 248862





































Search results

Summary of Contents for 248862

Reviews:

Related manuals for 248862

Brands by name

Popular brands

Graco 248862, Repair Parts List Manual

Search results

Summary of Contents for 248862

Reviews:

Related manuals for 248862

Brands by name

Popular brands