background image

307621

3

WARNING

INJECTION HAZARD

Spray from the gun, leaks or ruptured components can inject fluid into your body and cause extremely
serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin can also
cause serious injury.

D

Fluid injected into the skin might look like just a cut, but it is a serious injury. 

Get immediate medi-

cal attention.

D

Do not point the gun at anyone or at any part of the body.

D

Do not put your hand or fingers over the spray tip.

D

Do not stop or deflect leaks with your hand, body, glove or rag.

D

Do not “blow back” fluid; this is not an air spray system.

D

Always have the tip guard and the trigger guard on the gun when spraying.

D

Check the gun diffuser operation weekly. Refer to the gun manual.

D

Be sure the gun trigger safety operates before spraying.

D

Lock the gun trigger safety when you stop spraying.

D

Follow the 

Pressure Relief Procedure

 on page 8 if the spray tip clogs and before cleaning,

checking or servicing the equipment.

D

Tighten all fluid connections before operating the equipment.

D

Check the hoses, tubes, and couplings daily. Replace worn or damaged parts immediately. 
Do not repair high pressure couplings; you must replace the entire hose.

MOVING PARTS HAZARD

Moving parts, such as the air motor piston, can pinch or amputate your fingers.

D

Keep clear of all moving parts when starting or operating the pump.

D

Before servicing the equipment, follow the

 Pressure Relief Procedure

 on page 8 to prevent the

equipment from starting unexpectedly.

Summary of Contents for 226970



















Reviews: