Graco 223688 Instructions-Parts List Download Page 3

308034   3

Turbine Alternator Service

KEY

A

B

  

D

E

!

G

  

1

2

3

101

101a

 

NOTE: The items referenced with numbers
are included with a kit.

 

Exhaust Port

Exhaust Port

Fig. 1

Model PRO 3500,
Model PRO Pulse,
and SuperCat

Model PRO 4000
and Model PRO 5000

PRO 4000 &

PRO 5000 only

Assembly

1.

Remove the bearings (1 & 2) from the package
and wipe the excess oil off with a soft cloth. Do not
use solvent or air to wipe or blow off the excess oil.

2.

Place the smaller bearing (1) 

[marked 179395] on

the long end of the armature (D), with the ma-
chined groove in the bearing facing the armature.

3.

Install the fan (3) on the long end of the armature
(D), with the machined groove in the fan facing
away from the armature.

4.

Insert the spacing tool (4) between the fan (3) and
bearing (1). Lightly tap on the end of the armature
(D) until the fan is pressed up against the spacing
tool and bearing. Remove the spacing tool. When
properly installed, the bearing (1) should spin
freely on the armature shaft.

5.

Install the coil assembly (101) over the armature
(D), with the 3-wire connector (101a) facing away
from the fan (3).

6.

Place the larger bearing (2) 

[marked 179396] on

the end of the armature (D), with the machined
groove in the bearing (2) facing in toward the
armature. Align the legs of both bearings with each
other.

NOTE: When installed, the bearing legs must not block
the exhaust ports of the turbine alternator housing (B)
or the gun will not operate properly.

7.

Carefully slide the turbine alternator housing (B)
over the turbine assembly (G), aligning the bearing
legs between the exhaust ports of the housing.
Push the turbine alternator housing onto the
turbine assembly until the assembly is seated
firmly in the turbine alternator housing.

8.

Press the plastic plug (A) onto the back of the
turbine alternator housing (B).

9.

PRO 4000 and PRO 5000 only: Install the metal
retaining clip (H).

10. Install the turbine alternator on the power cartridge

as instructed in your spray gun manual.

11. Install the power cartridge and assemble the gun.

Summary of Contents for 223688

Page 1: ...nt warnings and information READ AND KEEP FOR REFERENCE Turbine Alternator Repair Kits Part No 223688 Bearing Repair Kit Part No 223750 Coil Repair Kit These repair kits are for use with Models PRO 3500t PRO 4000r and PRO 5000t Series Electrostatic Spray Guns with Model PRO Pulse Electronic Fluid Meter and with SuperCatt Proportioners GRACO INC P O BOX 1441 MINNEAPOLIS MN 55440 1441 ECOPYRIGHT 199...

Page 2: ...ocedure in your spray gun manual or in the SuperCat instruction manual Disassembly 1 Relieve the pressure 2 See your spray gun manual to remove the power cartridge For the SuperCat alternator remove six screws open the housing and remove the power cartridge 3 Remove the turbine alternator 4 Test the Coil Measure the resistance between the two outer terminals of the 3 pin connector 101a The resista...

Page 3: ...rly installed the bearing 1 should spin freely on the armature shaft 5 Install the coil assembly 101 over the armature D with the 3 wire connector 101a facing away from the fan 3 6 Place the larger bearing 2 marked 179396 on the end of the armature D with the machined groove in the bearing 2 facing in toward the armature Align the legs of both bearings with each other NOTE When installed the beari...

Page 4: ... Number TO PLACE AN ORDER contact your Graco distribu tor or call this number to identify the distributor closest to you 1 800 367 4023 Toll Free All written and visual data contained in this document reflects the latest product information available at the time of publication Graco reserves the right to make changes at any time without notice Sales Offices Minneapolis Detroit Foreign Offices Belg...

Reviews: