background image

WARNING

INJECTION HAZARD

Fluid dispensed from the gun, leaks or ruptured components can inject fluid into your body and cause
extremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin
can also cause serious injury.

D

Fluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate medi-
cal attention.

D

Do not point the gun at anyone or at any part of the body.

D

Do not put your hand or fingers over the nozzle.

D

Do not stop or deflect leaks with your hand, body, glove or rag.

D

Do not “blow back” fluid; this is not an air spray system.

D

Be sure the gun trigger safety operates before dispensing.

D

Fully release the trigger to lock the gun trigger safety when you stop dispensing.

D

Follow the Pressure Relief Procedure on page 5 if the nozzle clogs and before cleaning, check-
ing or servicing the equipment.

D

Tighten all fluid connections before operating the equipment.

D

Check the hoses, tubes, and couplings daily. Replace worn or damaged parts immediately. Do not
repair high pressure couplings; you must replace the entire hose.

D

Fluid hoses must have spring guards on both ends, to help protect them from rupture caused by
kinks or bends near the couplings.

RECOIL HAZARD

Due to the high pressure fluid emitted, a strong recoil action may occur when you trigger this gun. If
you are unprepared, your hand could be forced back toward your body or you could lose your balance
and fall, resulting in serious injury.

Summary of Contents for 207-945













Reviews: