IV. Specifications:
- DMX512 with 6 channels
- Functions: DMX512, automatic operation, sound activated, master/slave
- super bright 1W LED lamp
- 7pcs x3W LED lamp (RGB 3 in 1) red, green, blue
- color temperature less than 6000k
- 0 – 100% dimmer
- multi-flash effect: gradually open and close flash, 1 – 10 times per sec
- low power consumption, est. 100,000 hour life span
- voltage: AC90V-240V/50 or 60Hz
- power: 30W
- 5.5in x 5.5in x 7.5in
- 4lbs
I. Operation
This light has 4 functions:
1. DMX512 with 6 channels
2. Automatic operation
3. Sound Activated
4. Master/slave
II. Menu (for use without controller):
When you press the “MENU” switch there will be the following
menu options: (Digital Memory: to save your settings even if you
lose power hold the “ENTER”)
●
[D001]: This is the DMX address of this fixture. You can press “UP” or
“DOWN” to set it from [D000] up to [D512] and press “ENTER” to
confirm it. This function allows you to put the light fixture in DMX
mode so that you may use a controller if needed.
●
[Fxxx]: This is the strobe effect. You can press “UP” or “DOWN” to set
the strobe effect from [F000] up to [F255] and press “ENTER” to
confirm it. Adjusting the number value of this effect will change the
speed at which the strobe effect blinks.
●
[Pxxx]: This is the automatic color alternating effect. You can press “UP”
or “DOWN” to set the speed from [P000] up to [P255] and press
“ENTER” to confirm it. Adjusting the number value of this effect
will adjust the speed at which the color alternates.
●
[Lxxx]: This is the color cross fade in/fade out effect. You can press “UP”
or “DOWN” to set the speed from [L000] up to [L255] and press
“ENTER” to confirm it. Adjusting the number value of this effect
will adjust the speed at which the colors fade in and out over each
other.
●
[Exxx]: This is the separate color fade in/fade out. You can press “UP” or
“DOWN” to set the speed from [E000] up to [E255] and press
“ENTER” to confirm it. Adjusting the number value of this effect
will adjust the speed at which it takes the old color to fade out before
a new color can fade in.
●
[SOUD]: This is the sound activated function. When set on this mode the
lights will alternate based on the sound picked up by the built in
microphone inside this fixture.
●
[Rxxx]: This is the red color dim. You can press “UP” or “DOWN” to set
it from [R000] up to [R255] to dim the red color and press “ENTER”
to confirm it.
●
[Gxxx]: This is the Green color dim. You can press “UP” or “DOWN” to
set it from [G000] up to [G255] to dim the Green color and press
“ENTER” to confirm it.
●
[Bxxx]: This is the blue color dim. You can press “UP” or “DOWN” to set
it from [B000] up to [B255] to dim the blue color and press
“ENTER” to confirm it.
Channel
Function
CH1
Dim
CH2
Red
CH3
Green
CH4
Blue
CH5
0 – 50
No function
51 – 100
Color alternating
101 – 150
Cross fade in/fade out
151 – 200
Separate fade in/fade out
201 – 255
Sound activated
CH6
Strobe
Menu Panel
(on back)
III. DMX Channel List (for use with controller):
Note: to enter DMX mode press the “MENU” button located on the
back of the light until the display reads “[D001]” and then press enter.
