manualshive.com logo in svg

Gossen MetraWatt METRACLIP 62, Operating Instructions Manual, Page: 6 / 17

Share
Download
Gossen MetraWatt METRACLIP 62 Operating Instructions Manual Download Page 6

6

GMC-I Messtechnik GmbH

Attention!

!

Do not perform measurements in the 
event of over-ranging! 

Current which exceeds the measuring 
range may not be measured. 

Do not perform measurements at bare 
wires! 
Do not perform measurements at busbars! 

Safe Handling

•

The housing and the handles must be free 
of dust, grease and moisture.

•

The operator’s fingers may not be 
extended beyond the safety collar during 
measurement.

•

Avoid excessive mechanical stress such 
as impact and vibration, as well as high 
temperatures, moisture and strong 
magnetic fields.

•

The battery compartment lid must be 
secured with the appropriate Phillips head 
screw.

1.1

Special Features of the Hall Effect Sensor

Eliminating the influence of magnetization

The clip-on ammeter 

METRA

CLIP

62

 uses the 

hall effect for its measurements. The charac-
teristics of the hall effect are subject to a hys-

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for METRACLIP 62


















Reviews:

No comments