background image

GMC-I Gossen-Metrawatt GmbH

29

GB

20

Repair and Replacement Parts Service
DKD Calibration Lab* and Rental Instrument Service

If required, please contact:

GMC-I Gossen-Metrawatt GmbH

Service-Center

Thomas-Mann-Strasse 20
90471 Nürnberg • Germany
Phone

+49-(0)-911-8602-0

Fax +49-(0)-911-8602-253
E-Mail

[email protected]

This address is only valid in Germany. Please contact our represen-
tatives or subsidiaries for service in other countries.

*  

Calibration 

Laboratory 

for Electrical Quantities DKD–K–19701
accredited per DIN EN ISO/IEC 17025

Accredited measured quantities: direct voltage, direct current 
values, DC resistance, alternating voltage, alternating current 
values, AC active power, AC apparent power, DC power, 
capacitance and frequency

DKD Calibration Certificate Reprints

If you need to order a reprint of the DKD calibration certificate for 
your instrument, please include the ID number shown in the upper-
most and lowermost fields of the calibration certificate. We do not 
need the instrument’s serial number.

21

Warranty

The warranty period for all measuring and calibration instruments of 
the METRA HIT series is 3 years from delivery.
The warranty period for calibration is 12 months. Warranty covers 
faulty workmanship and material, not including any damage caused 
by improper use and any follow-up costs.

22

Product Support

If required, please contact:

GMC-I Gossen-Metrawatt GmbH

Product Support Hotline 

Phone +49-(0)-911-8602-112
Fax +49-(0)-911-8602-709
E-Mail

[email protected]

Summary of Contents for METRA HIT 16I/L































Reviews: