manualshive.com logo in svg

Gossen MetraWatt ECUTEST ST BASE, Condensed Operating Instructions, Page: 39 / 56

Share
Download
Gossen MetraWatt ECUTEST ST BASE Condensed Operating Instructions Download Page 39

Gossen Metrawatt GmbH

39

SECU

TEST ST 

B

ASE

(

10

) / 

P

RO

 

and SECU

LIFE ST 

BASE

(25)

13.15 EL1 – Function Test for Extension 

Cords

Attention!

!

This function permits an evaluation of 
the continuity of the active conduc-
tors L(1, 2, 3) and N of an extension 
cord. The PE conductor isn’t tested 
in this case!

See corresponding single measurements for 
the testing of R

PE

 and R

INS

. 

Note

See section 14 with regard to testing 
extension cords per DIN VDE 0701-
0702, for which R

PE

 and R

INS

 are 

measured.

Connecting the EL1 Adapter

➭

Connect the EL1 adapter to the P1 spe-
cial sockets at the test instrument.

➭

Connect the plug at the end of the ex-
tension cord to the test socket.

➭

Connect the coupling socket at the end 
of the extension cord to the plug at the 
EL1 adapter.

Connecting Test Adapters VL2E and AT3-IIIE

➭

Connection examples can be found in section 
13.19.

Continuity test for L and N

Meas. Parameter

Test for

Measurement type

Continuity 

L(1/2

/3)

, N

Short-c

ir

cuit 

between 

L(1/2

/3)

, N

Re

versed po

lar

ity /

 

cl

oc

kwise 

phase sequence

EL1 adapter

X

X

—

EL1 adapter 
(continuity only)

X

—

—

VL2E adapter 

X

X

X

AT3-IIIE adapter

X

X

X

Select measuring function

1

EL1

Select parameters

2

Set parameters

3

Connect the DUT

4

EL1 adapter

P1

VL2E adapter

Start test

5

Save measured values to clipboard

6

Stop test

7

Save measurements under ID no.

9

Summary of Contents for ECUTEST ST BASE

























































Reviews:

No comments