OM-07328
SUPER T SERIES
MAINTENANCE & REPAIR
PAGE E - 14
Aviation No. 3 Form‐A‐Gasket' or equivalent com
pound to the mating surfaces, and secure them to
the pump casing with the attaching hardware.
Back Cover Installation and Adjustment
(Figures 1 and 8)
If the wear plate (3) was removed for replacement,
carefully center it on the back cover (9) and secure
it with the hardware (6 and 7). The wear plate
must
be concentric to prevent binding when the back
cover is installed.
Clearance between the impeller and wear plate is
adjusted using four adjusting screws and locking
collars (17 and 20). There are 18 detents on the I.D.
of each locking collar. Indexing the collars one det
ent on the adjusting screws represents approxi
mately .005 inch (0,13 mm) of wear plate clear
ance. The recommended clearance between the
wear plate and the impeller is .010 to .020 inch
(0,25 to 0,50 mm).
Replace the back cover O‐rings (4 and 8) and lubri
cate them with a generous amount of No. 2 grease.
Clean any scale or debris from the contacting sur
faces in the pump casing that might interfere or
prevent a good seal with the back cover.
USE TWO
OPPOSING
BACK COVER NUTS
TO PRESS
BACK COVER
INTO PUMP
CASING
USE TWO REMAINING
ADJUSTING SCREWS AND
LOCKING COLLARS TO
SET FACE CLEARANCE
INDEX COLLARS 3
DETENTS COUNTER‐
CLOCKWISE, THEN
TURN CLOCKWISE
UNTIL SCREW
HOLES ALIGN
Figure 8. Installing and Adjusting Back Cover
Screw the four adjusting screws (20) into the
tapped holes in the back cover plate until they are
just flush
with the machined surface on the back
side of the cover plate.
Align the back cover plate over the studs (2) and
slide it into the pump casing. Use two back cover
nuts (19) on diagonally opposing studs to press
the back cover into the pump casing until the wear
plate
just touches
the impeller when the shaft is
turned by hand.
Tighten the back cover nuts
evenly to avoid binding.
With the wear plate just touching the impeller, turn
the two free adjusting screws until they engage the
pump casing. Position the locking collars over the
adjusting screws so the holes in the collars for the
locking screws align approximately with the holes
in the cover plate.
Loosen the back cover nuts used to press the back
cover into the pump casing one full turn.
Pull the collars off the adjusting screws, index them
three detents counterclockwise and reinstall the
collars on the adjusting screws. Use the collars to
turn the adjusting screws clockwise until the holes
in the locking collars realign with the tapped screw
holes in the back cover plate. Secure the locking
collars (10) to the back cover plate with the hard
ware (11 and 12). Install the two remaining back
cover nuts snugly against the adjusting screws.
Remove the first two back cover nuts from their
studs. Turn the adjusting screws clockwise until
they engage the pump casing. Install the locking
collars (10) and hardware (11 and 12). Reinstall the
back cover nuts.
Be sure the wear plate does not scrape against the
impeller.
Over time it may be necessary to repeat the adjust
ment process to compensate for normal wear be
tween the impeller and wear plate. When all of the
adjustment has been used on the back cover side
of the pump, an additional 0.125 inch (3,2 mm) of
adjustment may be obtained by removing the ro
tating assembly adjusting shims (33).
Allow an installed pump to completely cool before
draining liquid from the pump casing. Remove the
back cover. Remove the rotating assembly adjust
ing shims, then reinstall the hardware securing the
rotating assembly to the pump casing. Perform the
back cover adjustment procedure described
above to obtain the proper face clearance.
