manualshive.com logo in svg

Gorilla Playsets 1500BW, Manual, Page: 74 / 124

Share
Download
Gorilla Playsets 1500BW Manual Download Page 74

REAR PANEL SLAT SPACING

 2 34 " 

SCREW

2" WOOD

PANEL SLAT

5/4 X 2-5/8 X 28-1/4"

SWING BEAM

REAR PANEL

FRONT PANEL SLATS 

ARE INSTALLED FLUSH 

TO THE NOTCH ON 

PANEL

THE FRONT FACE 

BOARD.

LEAVE THIS SLAT OFF UNTIL AFTER 

INSTALLING THE TIRE SWING 

BEAM.  ONCE THE TIRE SWING 

BEAM IS IN PLACE SECURE THIS 

SLAT FLUSH TO THE SIDE OF THE 

SWING BEAM.

ROCK WALL

PANEL

2:  PRE-DRILL THE SLATS 1" FROM EACH END ON CENTER WITH A 1/8" DRILL BIT.

1:  FIND TWENTY-TWO 5/4 X 2-5/8 X 28-1/4" PANEL SLATS.

3:  INSTALL THE PANEL SLATS AT EQUAL LENGTHS.  SEE DETAIL BELOW FOR MEASUREMENTS.

ROCK WALL SIDE PANEL

4:  ATTACH THE PANEL SLATS TO THE FORT WITH 2" WOOD SCREWS IN THE PRE-DRILLED HOLES.

STEP 22:  PANEL SLATS

SWING BEAM PANEL

 

SLAT DIMENSIONS

(VIEW FROM OUTSIDE

THE PLAY SET.)

8

2

 2 1

16

" 

" 

9

 11

" 

 17 1

 2 18 " 

MAKE THIS SLAT FLUSH 

TO THE END OF 

THE 2 X 4 X 14" BOTTOM 

PANEL BOARD. SPACE 

THE NEXT SLAT EQUALLY 

BETWEEN THE FIRST SLAT 

AND THE CORNER 

POST.

66

Summary of Contents for 1500BW





























































































































Reviews:

No comments