Gorilla Playsets 1500ATNS Manual Download Page 62

Page: 62 / 76

PAN HEAD SCREWS.

TARP BOARD FOR THE

NOTE: IF YOU WISH

YOU MAY DRILL 1/8"

PILOT HOLES IN THE

TARP 47-3/8" X 105"

FASTEN OUTSIDE GROMMETS FIRST TO

HEAD SCREWS AND 1/4" WASHERS.

EACH SIDE WITH #14 X 1-1/4" PAN

REPEAT FOR OTHER SIDE.

(COLOR AND STYLES

MAY VARY)

THE SIDE OF THE TARP BOARD ON

THEN FOLD

THIS TAB UNDER

THE TARP BOARD

AND SECURE IT

TO THE BOTTOM

SIDE OF THE TARP

BOARD WITH

#14 X 1-1/4"

PAN HEAD SCREWS

AND 1/4" WASHERS.

REPEAT FOR OTHER

SIDE.

1: PLACE THE 47-3/8" X 105" TARP ACROSS THE TARP BOARDS WITH THE HEMS ON THE INSIDE.

2: FASTEN THE OUTSIDE CORNERS OF THE TARP TO THE SIDE OF THE TARP BOARD FIRST. ATTACH THE GROMMETS

IN THE TARP TO THE TARP BOARDS WITH #14 X 1-1/4" PAN HEAD SCREWS WITH 1/4" WASHERS. REPEAT FOR OTHER

SIDE. (NOTE IF YOU WISH YOU MAY PREDRILL HOLES FOR THE PAN HEAD SCREWS WITH A 1/8" DRILL BIT.)

3: NOW FOLD THE FLAP UNDER THE TARP BOARD ON AND FASTEN THE GROMMETS UNDER THE TARP BOARD WITH

#14 X 1-1/4" PAN HEAD SCREWS WITH 1/4" WASHERS. REPEAT FOR OTHER SIDE. (NOTE IF YOU WISH YOU MAY

PREDRILL HOLES FOR THE PAN HEAD SCREWS WITH A 1/8" DRILL BIT.)

STEP 21: TARP

Summary of Contents for 1500ATNS













































































Search results

Summary of Contents for 1500ATNS

Reviews:

Related manuals for 1500ATNS

Brands by name

Popular brands

Gorilla Playsets 1500ATNS, Manual

Search results

Summary of Contents for 1500ATNS

Reviews:

Related manuals for 1500ATNS

Brands by name

Popular brands