The sound will mute for approximately 1 second while the buffer fills. Once filled
the buffer will give approximately 180 seconds of protection against interruption
of sound output, If the player is subjected to shock of over 180 seconds duration
some interruption of sound output will occur, This is normal and to be expected,
The sound will resume once the player has stabilized from the shock.
To turn this function off press the ESP button.
Notes:
1. When using the ANTI-SKIP function the battery power consumption
increases because the disc rotates faster than normal and the dynamic
memory is active.
2. While the ANTI-SKIP function provides for continuous sound output
when the unit is subjected to shock or vibration, it will not correct errors
arising from the use of defective ,scratched or dirty discs.
3. When powering the player solely from batteries, only use the ANTI-SKIP
function where necessary to preserve their life.
This player incorporates the latest digital anti shock circuit, which prevents interruption
of the sound output if the unit is subjected to shock or vibration during disc playback.
The anti shock system will automatically start when a disc is played, is shown in the
display during start up and when shows the data buffer is full and the anti shock
system is it's most effective. If the anti shock function is not required then it can be
switched off by pressing the ESP button until the symbol disappears from the display.
ANTI-SKIP Indicator
ANTI-SKIP Indicator
ANTI-SKIP Indicator
12.DIGITAL ANTI - SHOCK OPERATION
13.RADIO OPERATION
1. Set the FUNCTION switch to RADIO for RADIO mode, press RADIO ON ( ) key.
2. Press the BAND key to select AM or FM.
Note : To improve reception, rotate the unit in all directions until best reception is obtained
(AM only).
3. Press the MODE button key to select FM MONO or FM STEREO (FM Band only).
4. To turn the radio off press RADIO OFF ( ) key.
Stereo /Mono
When listening to a radio station broadcasting in FM stereo, press the MODE
button to select stereo mode. The STEREO indicator will show in the display.
If the FM Stereo signal is weak, push the MODE button to select OFF(MONO)
mode (the station will be received in mono but the background noise will be reduced).
The stereo indicator will be off.
Aerial
AM : The unit is equipped with an internal rod aerial. For best reception, rotate the unit.
FM : The headphones cord acts as an aerial and must be fully extended for best
reception.
Manual Tune
To manually tune to a station briefly, press the Tune up or down ( or ) buttons until
the station is tuned in.
Automatic Tune
Automatically tune to a station , press and hold either tune up or down ( or )
buttons. The unit will automatically tune to and stop at the first Station of sufficient signal
strength.
MEMORIZING PRESET STATIONS
You can store up to 10 radio stations for each band into the memory.To memorize preset
stations:
1 Set the FUNCTION switch RADIO for RADIO mode.
2 Press the BAND button to select AM or FM.
3 Tune the desired station by pressing the Tuning UP/DOWN ( or ) buttons.
4 Press the PROG button. " PROG " indicator appear in the display.
5 Press the preset UP( ) or DOWN ( ) buttons to select the desired preset station
number.
6. Press the PROG button again to store the station in the required location.
7. Repeat steps 3 to 6 until all desired stations are programmed into the memory.
Notes :
When a new, different station is preset, the previous preset station will be
erased.
RECALLING PRESET STATIONS
1. Set the FUNCTION switch RADIO for RADIO mode.
2. Press the BAND button to select AM or FM.
3. Press the PLAY/PAUSE button to turn on RADIO.
4. Press the preset UP ( ) or DOWN ( ) buttons to select the desired preset station.
You can lock the controls on your CD player to
prevent accidental button presses. Slide HOLD in
the direction ON position even if the HOLD function
is working, it shows "HOLD" in the display.
OFF
ON
HOLD
LOCKING THE CONTROL
