71880
EN User Manual
Battery-powered screwdriver, 3.6 V with LED
- 3 -
Goobay
®
by Wentronic GmbH | Pillmannstraße 12
38112 Braunschweig | Germany
REV2019-01-03
V2.0tf
Original User Manual: German version
1 Safety Instructions
1.1 General
•
Read the user manual completely and carefully before use.
It is part of the product and contains important information for correct use.
•
Keep this user manual.
It must be available for uncertainties and passing the product.
Notes for network separation of the power supply
The product has no power switch and may be used only in easily acces
sible outlets to quickly remove it in an emergency and after use.
Voltage-free only with pulled plug.
•
In case of emergency, during thunderstorms and after use,
pull the product on its plug housing!
•
Only use the supplied power supply.
Battery hazards
The batteries are not replaceable.
•
Leave leaked, deformed or corroded batteries inside the
product and dispose it by appropriate protectives.
•
Do not throw into fire.
•
Avoid body contact with grounded surfaces.
Risk of entry
Rotating parts can pull loose clothing and hair.
•
Wear tight clothing.
•
Tie long hair before starting work.
Not recommended for children and people with physical and / or mentally
limited capabilities.
•
Do not open the housing.
•
Do not kink or stretch power cords.
•
Do NEVER let the product unattended in use.
•
Compare the specifications of product, power supply and
peripherals.
These must be identical.
•
Do not repair defective products by yourself, but contact the
dealer or producer.
•
Use product, product parts and accessories only in perfect
condition.
•
Do not modify or alter product nor accessories.
•
Avoid stresses such as heat and cold, moisture and direct
sunlight, vibration and mechanical pressure.
•
Risk of injury by stumbling and falling
•
Charge only on stabil, non-slipping, fire-prof and horizontal
surfaces.
•
Only use in dry ambience.
•
Do not operate in an explosive environment.
•
Do not short terminals.
•
Adapt protective equipment to work requirements.
1.2
Warning levels
Warnings against hazards that may result in
injuries
in case
of
non-observance.
Warnings against hazards that may result in
material
damage
in case of non-observance.
2
Description and Function
2.1
Battery-powered screwdriver, 3.6 V with LED
The cordless screwdriver is a hand-held tool for private home use. It allows the
screws to be screwed in and out, as well as the lighting of the screws. The product
can only be operated wirelessly.
2.2
Operating elements and parts
10
3
11
1
2
6
12
5
13
14
Fig. 3:
Operating elements and parts
1
Operation button
2
Direction selector switch ( | 0 | )
3
Bit holder
4
Battery status button
5
Bits (1x slot, 2x cross slot, 2x drill, Extension)
6 Handle
7
Battery status red (<20 %, EMPTY)
8
Battery status red+yellow (20-70 %)
9
Battery status red+green (>70 %, FULL)
10
Power supply unit
11
LED lighting
12
Eyelet for accessory flap
13
Lock for conversion
14
Torque switch
2.3
Scope of Delivery
Cordless screwdriver, 3 bits, 2 drills, extension, power supply unit, user manual
3
Intended Use
We do not permit using the device in other ways like described in chapter
Description and Function. Use the product only in dry interior rooms. Not
attending to these regulations and safety instructions might cause fatal
accidents, injuries, and damages to persons and property.
Any use, not mentioned in this user manual, in particular explicitly forbidden actions,
is considered to be non-intended.
4 Preparing
•
Charge the battery-powered screwdriver before first use completely.
If the first charge operations performed incompletely, it may negatively
affect the battery capacity.
5
Charging the battery-powered screwdriver
Risk of injury by tripping and falling
Cables can be overlooked.
•
Lay the cables in a safe way.
Material damage
Battery duration and battery life may deteriorate.
•
Charge only at ambient temperatures
b10 ~ +40 °C.
1.
Plug the supplied power supply unit into the DC connector on
the front bottom of the cordless screwdriver and into a free
and easily accessible mains socket.
The battery status lights up
red
during charging. During charging, the
cordless screwdriver cannot be switched on and used. Charging takes
~ 3-5 hours.
2.
Press the button for the battery status.
Battery status red
(<20 %, EMPTY),
battery status red+yellow
(20-70 %),
battery status red+green (>70 %, FULL)
3.
Disconnect the cordless screwdriver after charging from the
power
supply.
6 Assembly
•
Mount one of the supplied screw or drill attachments accor-
ding to the work to be performed.
There is a permanent magnet inside the bit holder, which prevents the
screw inserts from slipping out.
7 Conversion
The cordless screwdriver can be operated in pistol form, but also in screwdriver
form.
1.
Hold the cordless screwdriver by the handle.
2.
Press the conversion lock to convert it, and at the same time
turn the front part of the battery screwdriver into the desired
position until it clicks into place.
Fig. 4:
Conversion
8 Operating
Risk of entry
Rotating parts can pull loose clothing and hair.
•
Wear tight clothing.
•
Tie long hair before starting work.
1.
Select the safety equipment, such as gloves, gog-
gles, etc., according to the type of activity and the
environmental conditions as well as materials.
2.
Set the required direction of rotation by means of
the direction selector switch (2) and the torque by
means of the torque switch (14).
3.
Hold the cordless screwdriver by the handle and
press with sufficient force.
4.
Press the operation button (1) to operate.
5.
Release the operation button (1) after operation
before pulling the bit out of the screw.
After releasing, the electric motor rotates about 0.5 s.
The working time per battery charge is max. ~ 45 minutes.
9
LED lighting
The LED light works during operation by pressing the operation button.
