2
3
MOUNTING CONFIGURATIONS
*
( )
*
( )
For more information, see the T4503/NFC user manual (code 50122088).
https://doc.golmar.es/search/manual/50122088
SAFETY PRECAUTIONS
-
Always disconnect the power supply
before installing or making modifications to the devices.
-
The fitting and handling of these devices must be carried out by
authorised personnel.
-
The wiring must run at least
40cm. away from any other wiring.
-
On the power supply unit:
w
Do not overtighten the screws on the connector.
w
Install the power supply unit in a dry protected location free from the risk of dripping or splashing
water.
w
Avoid locations that are humid, dusty or near heat sources.
w
Ensure that the air vents are free from obstruction so that air can circulate freely.
w
To avoid damage, the power supply unit must be firmly secured in place.
w
To prevent electric shock, do not remove the cover or handle the wires connected to the
terminals.
-
NFC access control module (Golmar proximity cards).
- C
an be combined with 'Nexa Modular' and 'Inox Modular' door panels.
-
Basic configuration using the SW1 configuration DIP switch or Master card.
-
Advanced configuration and management of the NFC access control. Mobile with NFC and AC
Manager app required (Android only), see the
TAC Manager manual (code 50124945).
-
Enables management of the residents' card/key tag to activate the lock release of the NFC
access control via mobile. Mobile with NFC and OpenGo app required (Android only), see the
TOPENGO manual (code 50124946).
-
Status LED and tones.
CHARACTERISTICS
*
( )
DESCRIPTION OF THE MODULE
*
( )
a
b
c
a.
Front.
b.
Proximity card reader.
c.
Status LED (two-colour red/green).
d.
Back.
e.
Monitor connector.
f.
SW1 programming DIP switch.
g.
P1 programming button.
:
Power input.
:
Normally open output relay 1.
Common relay 1.
:
Normally closed output relay 1.
: Negative.
:
Input for exterior button relay 1.
~ ~
NA1
C1
NC1
-
PL1
NFC access control combined with Nexa button panels:
This equips the door panel with NFC access control, allowing users to make calls to apartments
using the call buttons. The site can also be accessed by waving a residents' card/key tag
(Golmar) over the EL4503/NFC module.
Add residents' cards/key tags:
set DIP switch 3 to ON, the LED on the
front will blink (red). Then wave the new residents' NFC/US cards /
TAGNFC/US key tags (Golmar) that you wish to add over the
EL4503/NFC proximity reader one by one, the module will emit 2 tones
and the LED will light up (green) for one second every time a residents' proximity
card/key tag is memorised or the LED will blink rapidly (red) if the card/key tag has
already been memorised. Up to 2,000 cards/key tags can be memorised. To exit
'Add residents' cards/key tags' mode, set DIP switch 3 to OFF, the LED on the front
(red) will turn off.
Remove all residents' cards/key tags:
set DIP switches 1 and 3 to ON,
the LED on the front will blink (red). Then press the P1 programming
button for 5 seconds, the LED will blink rapidly (red); after 5 seconds,
the LED will light up (green) for 1 second and the module will emit 2 short
tones indicating that the process has been carried out successfully.
To exit 'Remove all residents' cards/key tags' mode, set DIP switches 1 and 3 to
OFF, the LED on the front (red) will turn off.
NEXA AUDIO AND VIDEO DOOR ENTRY SYSTEM - NFC ACCESS CONTROL MODULE
Programming relay 1 activation time by access with card/key tag:
set
DIP switch 5 to ON, the LED on the front will blink (red). Press and hold
down the P1 button, the red LED will turn off and the green LED will
blink; each blink will increase the minimum activation time of 3 seconds
already set at the factory by 1 second. Once the desired activation time
has been selected, stop pressing the P1 button, the module will then emit 2 short
tones and the LED will light up (green) for 1 second confirming the new activation
time.
If you wish to reset the default time of 3 seconds, press the P1 button.
To exit 'Relay 1 activation time with card/key tag' mode, set DIP switch 5 to OFF, the
LED on the front (red) will turn off.
Continued overleaf.
*
( )
For more information, see the T4503/NFC user manual (code 50122088).
https://doc.golmar.es/search/manual/50122088
d
e
g
f
Description of the monitor connector:
P1
SW1
P1
SW1
P1
SW1
DESCRIPTION OF THE DOOR PANEL
*
( )
Exploded view of the parts of the panel.
Aluminium panel
Electronic
modules
Frame modules
Embedding boxes
*
( )
NEXA AUDIO AND VIDEO DOOR ENTRY SYSTEM - NFC ACCESS CONTROL MODULE
