5
Avoid dusty or smoky environments or locations near sources of heat.
For proper installation, use the template supplied with the product.
1. Position the top of the template at a height of 1.65m.
2. If you are going to use an embedding box to pass the wiring through, make sure that it is in line with the holes
corresponding to the box model chosen and fix the connector. If you prefer to fix the connector directly to the
wall, make four 6mm holes at the points indicated (A), insert the wall plugs supplied and screw in the connector.
3. Pass the installation wires through the middle hole and connect them to the removable terminals as shown in the
wiring diagrams. Before connecting the removable terminals to the monitor, configure the switch as indicated below.
4. Connect the removable terminals to the monitor and place the monitor in front of the connector, making sure the
fixings line up. Move the monitor downwards to secure it.
INSTALLATION
INSTALLATION TERMINALS (J)
For ease of installation, the installation terminals are removable and supplied in a separate bag. Once the
terminals are wired, place them in position.
BUS, BUS: Communication BUS (non-polarised).
SA, GND: Auxiliary call repeater output (max 50mA/12V), relay SAR-12/24.
HZ, HZ: Apartment front door button input:
Connect only on the master monitor. The signal received is then transmitted
to the slave monitors in the same apartment through the BUS.
CONFIGURATION SWITCHES (I)
Note: HZ push button function mode:
When HZ push button is pressed will be call tone and activate the output of
auxiliary call repeater with standby monitor, call process, communication process (HZ tone with lower audio level),
intercom process and "Do not disturb" mode.
Important:
Up to 6 monitors/ apartments with push button "HZ"
activated at the same time (with system and monitors in standby).
SA
GND
HZ
HZ
O
N
1
2
3
4
5
6
7
8
BUS
BUS
ART4WH/G2+ monitor with V.01 and next (addresses 1 to 128):
Switches
to 7
1
:
1
2 ).
to 1 8
Sets the monitor address (addresses
The switches set to OFF have a zero value. The values of the switches set to ON are shown in the table below. The
monitor code is the sum of the values of the switches set to ON.
Switch 8:
This activates the end-of-line resistance in the ON position. Activate it in monitors where the bus cable
ends. Deactivate it only in intermediate monitors.
Note:
To de
fi
ne whether the monitor is master or slave:
To de
fi
ne whether the monitor is master or slave (see special codes page
to 32).
30
Each apartment must have one master monitor, and only one.
Important:
Apartment 1 (Dip1 to ON & Dip2-Dip to OFF)
7
Important:
Apartment 128 (Dip1 - Dip7 to OFF).
Switch number
6 7
: 1 2 3 4 5
: 1 2 4 8 16
Value when ON
32 64
Table of values
1
2
3
ON
E
mpl : 0
xa
e
0+0
+ 0+4+0+16+
= 20
4
5
6
7
8
ART 4WH/G2+ MONITOR
Dip1 to Dip :
7
These assign the address of the monitor to call button on the door panel.
Switches - must remain in the OFF position.
2 7
Dip8:
This activates the end-of-line resistance in the ON position. Activate it in monitor where the bus cable ends.
Deactivate it only in intermediate monitors.
Not :
e
To de
fi
ne whether the monitor is master or slave, entering the
corresponding
“
Special code
”
: "0550" Master (factory default),
1,
”
0551" Slave
“
0552" Slave or
“
0553" Slave .
2
3
Villa (Kit Soul S5110 Access)
1
2
3
ON
4
5
6
7
8
Apartment 1
1
2
3
ON
4
5
6
7
8
Dip 8 a ON
1
2
3
ON
4
5
6
7
8
Dip 8 a OFF