background image

 

GOLDMUND TELOS 500 - Universal Power Amplifier - 12 

6  

SOUND QUALITY OPTIMIZATION 

 
 
 

WARM-UP SONIC EFFECT 

 
When the amplifier has not been used recently it will take 10 to 15 minutes for the amplifier 
to reached optimum operating temperature, as the circuits have to warm up to 55 
degrees Celsius. 
 

SPEAKER POLARITY 

 
Even  if  you  have  a  phase  inverter  on  your  preamplifier  and  have  carefully  selected  the 
proper line phase (see next paragraph below), there is a possibility to further increase the 
sonic  quality  of  your  speakers  by  reverting  the  polarity  of  the  speaker  cable  amplifier 
termination.  Line  phase  and  speaker  polarity  interfere  with  each  other  however.  We 
therefore advise careful experimentation with all the combinations in order to arrive at the 
best solution for your installation. 
 
If your preamplifier has an absolute phase inverter, this will interfere too. If it has not, don't 
forget the result will depend on the source, as most records and CDs have been recorded 
without care for the absolute phase. Be patient… 
 

MAIN LINE PHASE INVERSION 

 
To  select  the  proper  phase,  you  have  to  select,  by  trying,  one  of  the  two  power  cord 
positions. 
 
We recommend that you proceed carefully when trying this. You must do it in combination 
with the speaker polarity and/or with absolute phase switching to be sure of the result. 
 
 
 

Summary of Contents for TELOS 500



















Reviews: