background image

 

GOLDMUND LOGOS ANATTA Active Speaker - 8 

CONNECTIONS 

 

 

Wiring:  

Usable in any type of configuration, the LOGOS ANATTA has built-in amplifiers with built-in 
input DSP crossovers. The input is an unbalanced digital input (S/PDIF). 
 
When  used  with  a  digital  input  signal,  connect  the  digital  cable  to  the  digital  input 
connector.  

 
Wireless: 

To achieve optimal performance, please observe the following points: 
 

  The  LOGOS  ANATTA  and  the  USB  dongle  or  Wireless  Transmitter  should  be 

placed in the same room. 

  There  should  be  no  metallic  obstacles  between  the  USB  dongle  or  Wireless 

Transmitter and the LOGOS ANATTA, which could influence the wireless link. 

  The computer with the USB dongle should not be moved around during playback. 

 

Wireless audio link range: 

The  range  of  the  wireless  audio  link  depends  on  several  factors,  such  as  the  amount  of 
WiFi equipment used in proximity of the LOGOS ANATTA system, as well as the building 
materials and the architecture of the room. 
 
Depending on the above mentioned factors, the maximum range will normally be from 5 to 
20 meters. 
 
To use the LOGOS ANATTA in wireless, follow these steps: 
 

  Connect the speaker to a mains outlet using the power cords contained in the box. 

 
 
 
 
 
 

Summary of Contents for Logos Anatta













Reviews: