background image

 

7

6. Top woofer connection and mounting. 

 
 
 
For each speaker you will need: 
 

- 1 top woofer section 

(Top Woofer Right or Left) 

 

- 2 threaded bars 

           (Tweeters) 

 

- 4 molettes                        (Molettes) 

 
Place the top woofer behind the bottom woofer, near its definite position, with its 
cable directed towards the bottom woofer, in order to facilitate the connection of 
the cable to the bottom crossover section located on top surface of the bottom 
woofer. Each cable is built with a black and white wire already tinned. Solder each 
cable to the corresponding lugs on the bottom crossover section (see fig. 1). 
 
Pass the soldered cable through the cable holder at the bottom of the crossover to 
avoid any tension on the solder joint. 
When you lower the top woofer towards the bottom one, roll the cable around the 
cylindrical protection of the groove in the crossover. This is necessary in order to 
avoid crushing the cable when the pointed footof the top woofer passes through 
the groove. 
 
Then pass the other cable, which is attached to the bottom crossover section, from 
bottom to top, through the hole which goes through the top woofer section. Turn 
the cable on itself if you have difficulties to pass it through. 
When you lower the top woofer towards the bottom one, pull the cable passing 
through the top woofer section to avoid any loops over the bottom crossover 
section. 
 
In aligning the two woofers (bottom and top), the top pointed foot must be inserted 
in the groove in the crossover located on top of the bottom woofer through the 
cylindrical protection. 
Level the woofers using the back adjustable feet. 
The two woofers must be aligned exactly vertically. 
 

Warning :

 This operation requests four people. Two to hold the top woofer section 

from the back of the enclosure assembly, one to catch the woofer from the front, 
and one to roll the cable and to insert the pointed foot in the cylindrical protection. 
 
When the top woofer is in position, insert two threaded bars, screwing, through the 
frame's oblique legs, in the holes at the sides of the top woofer section. 
 
You can now tighten the basis of the frame's two oblique legs using an angled 
allen key. Set them so that the top bar is perfectly horizontal. 
 
Screw 4 molettes on the woofer assembly. 
 
 
 
 

Summary of Contents for APOLOGUE













Reviews: