manualshive.com logo in svg

Golden Companion, Service Manual, Page: 25 / 29

Share
Download
Golden Companion Service Manual Download Page 25

WWW.GOLDENTECH.COM

[email protected]

PAGE - 25

12. Remove the upper main harness clip. 

(See #1 on

figure 31.)

13. Remove the lower main harness clip. 

(See #1 on

figure 32.)

14. Unscrew the nut that secures the headlight

LEDs. 

(See #2 on figure 32.)

15. Feed the main harness through the rubber boot

and through the front shroud opening.

16. Turn the front frame over onto its right side.

17. Remove the controller cover.

18. Disconnect the 14-pin main harness connector

from the controller. 

(See #1 on figure 33.)

19. Disconnect the 2-pin main harness connector

from the 2-pin taillight connector. 

(See #2 on

figure 33.)

20. Loosen the main harness clamp located just

above the front wheel on the front frame. 

(See

#1 on figure 34.

21. Remove the main harness.

22. Install the new main harness under the floor

board. Make sure that it is placed in the channel

on the front frame.

23. Connect the 14-pin main harness connector to

the controller.

24. Connect the 2-pin main harness connector to the

taillight connector.

25. Feed the main harness through the front shroud

opening.

26. Secure the main harness to the front frame with

the main harness clamp located above the front

wheel.

27. Turn the front frame over.

28. Feed the main harness through the rubber boot.

29. Secure the main harness and the headlight LED

harness to the tiller with the lower main harness

clip.

30. Secure the main harness and the headlight LED

harness to the tiller with the upper main harness

clip.

31. Reinstall the front tiller shroud.

32. Connect the main harness to the control panel,

the charger harness, the paddle pot, and the

headlight LEDs.

33. Reinstall the rear tiller shroud.

34. Reinstall the six screws that fasten the front

shroud and floorboard to the frame.

35. Reinstall the carpet.

36. Reconnect the front and rear frame sections.

37. Reinstall the batteries.

38. Reinstall the rear shroud.

39. Reinstall the seat.

Figure 32. Lower Harness Upper Clip

2

1

Figure 33. Controller Connection

1

2

1

Figure 34. Main Harness Frame Clamp

REAR

Summary of Contents for Companion






























Reviews:

No comments