manualshive.com logo in svg

Golden BUZZ ABOUT GP164, Owner'S Manual, Page: 16 / 40

Share
Download
Golden BUZZ ABOUT GP164 Owner'S Manual Download Page 16

16 

 

       V. DISASSEMBLY and BATTERY REPLACEMENT

                                                                                                                             

 
To disassemble your BUZZ

TM

ABOUT, follow the instructions listed below. 

  
 
 

 

 

Make certain that the controller power is turned off and that the chair is NOT in 
freewheel mode before attempting to perform disassembly. 

 

Never  use  your  BUZZ

TM

ABOUT’s 

wheels  or  arm  assemblies  as  a  handle.  The 

wheels may rotate and/or the arms may pull out of the seat, which can cause an 
injury and/or damage to the power chair. 

 

Refer  to  the  “Technical  Specifications”  section  in  this  manual  for  the  battery 
pack weight. Please get help if you do not feel capable of safely lifting that much 
weight. 

 
Disassembly  

1.

  Disconnect the joystick cable from the power module cable. Note: The joystick can be            

removed to reduce weight.

 

2.  Fold the seat back down. Note: Seat arms can be removed to reduce weight. 
3.  Grasp the seat firmly on each side, and lift up to remove. 
4.  Remove the battery pack by pulling up on the handle. 
5.  Grasp the frame and locking handle; lift the handle to unlock, and lift the frame up 
and off the drive train. See figure 7. Note: To reassemble the power chair, simply reverse 
the process. 

 

 

 
 
 
 
 

 

        

 
 
 
 
 
 
 

 
 
Battery Replacement 
Should  your  batteries  need  replacement;  please  contact  your  Golden  Technologies       
representative.  Battery  replacement  requires  disassembly  of  the  battery  pack  and  must 
be performed by a qualified technician.             
 
 
                 MANDATORY! Use only AGM or GEL-cell batteries.     

 

Figure 7

 

GP164 Shown Disassembled 

Battery Pack 

Summary of Contents for BUZZ ABOUT GP164









































Reviews:

No comments