background image

INSTALLATION AND OPERATING INSTRUCTIONS

GOLDEN BLOUNT

EL GRANDE

MODEL HD5030-TV TOP-VENT FIREPLACE

CSA APPROVED FOR NATURAL GAS OR PROPANE GAS

IMPORTANT!  Read all instructions carefully before starting

installation.  Failure to follow these instructions may result in

property damage, personal injury or possible loss of life.

WARNING: If the information in these
instructions is not followed exactly, a
fire or explosion may result causing
property damage, personal injury or
death.

– Do not store or use gasoline or other

flammable vapors and liquids in the
vicinity of this or any other appliance.

 – WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch;

do not use any phone in your
building.

• Immediately call your gas supplier

from a neighbor’s phone. Follow the
gas supplier’s instructions.

• If you cannot reach your gas

supplier, call the fire department.

– Installation and service must be

performed by a qualified installer,
service agency or the gas supplier.

The Flue Damper must be in the full
open position when burning the gas
logs.

This fireplace is to be burned only with
the gas log set supplied with the
fireplace.  Burning other items could
cause a fire hazard or injury.

For best results, Natural Gas pressure
should be 7" to 12" W.C. and 11" W.C.
for Propane Gas.

To simulate real wood burning, the gas
burner is designed to burn a yellow
flame.  It is normal for the logs to soot-
up.  The soot can be easily removed
with a vacuum cleaner or soft brush.

Check the label on the firebox to
assure the proper gas type.  Never
use anything but the correct gas type
for your fireplace.

This appliance complies with National
Safety and is tested and listed to ANSI
Z21.50A - 1998  as Vented Gas fireplaces.
Installation must conform to local codes.
In the absence of local codes,  installation
must conform with the current National
Fuel Gas Code, ANSI Z223.1.

Massachusetts State Code requires
damper to be welded open or removed.

9/05

MANUFACTURED BY:

4301 WESTGROVE DRIVE

ADDISON, TX  75001

INSTALLER/CONSUMER RETAIN THIS APPLIANCE

MANUAL WITH THE INSTALLED APPLIANCE

Summary of Contents for EL GRANDE HD5030-TV






















Reviews: