![background image](http://html.mh-extra.com/html/goldair/gpct500/gpct500_operating-instructions_2239955003.webp)
WARNING Keep all objects at least 1 metre from
the front, sides and rear of the appliance.
Note: When the heater is turned on for the first time,
it may release a slight, odour or smoke. This odour
or smoke is a normal occurrence caused by the
initial heating of the internal heating elements and
should not occur again.
HEAT CONTROL SWITCH
Check that the Power Switch at the back of the
heater is set to the Off position before plugging the
heater in and turning on the mains supply.
Turn the Power Switch at the back of the heater to
the
“I” position. You will hear a beep.
Press the Power button on the control panel to turn
the heater on, the LED will display the current room
temperature and the unit will begin to operate in Low
Heat mode.
To turn the unit off, press the Power Button on the
control panel first, the fan will continue to run until
the 10 second countdown timer has reached
“0”,
even though the elements have switched off. This is
normal. Turn the Power Switch at the back of the
heater to
“O” position and switch off at the mains
supply.
For greater economy, use the High Heat setting
initially and then switch to the Low Heat setting.
For the Low and High Heat settings the fan remains
at the same speed; only the element changes to
create the greater/lesser heat output.
THERMOSTAT
Press the Timer & Thermostat button twice, then use
the
“+” and “-” buttons to adjust the temperature to
your desired setting (from 5-35°C). Once you have
set the desired temperature, the LED will display the
room temperature again and will rise as the room
temperature increases.
The heater will now cycle on and off to maintain the
set temperature.
How the set temperature is maintained:
If the room temperature is higher than the set
temperature, the heater shuts Off automatically.
If the room temperature is lower than the set
temperature, the heater automatically switches itself
back On.
Operating your Ceramic Tower Heater
Always choose a safe location for the heater, keeping in mind the safety
precautions outlined. Ensure all packaging has been removed from the
unit before use. This appliance requires no installation, it should be used
solely as a portable appliance.
OSCILLATE
This button turns the heater oscillation function on
and off.
ECO
In Eco function the default set temperature is 22
℃
and cannot be adjusted.
If the room temperature drops below 18
℃
in Eco
mode the unit will adjust to operate in High Heat until
18
℃
is reached and then it will change to Low Heat
until 22
℃
is reached.
TIMER
Press the Timer & Thermostat button once, then use
the
“+” and “-” buttons to adjust the length of time
from 1
– 12hours that you would like the heater to
run for before turning off. Each press of the
“+” or “-”
button will adjust the length of time in 30 minute
increments before the unit switches off.
The selected number of hours will set after 5
seconds and will display on the LED screen. To turn
the Timer off, set the hours back to
“0” or simply turn
power off .
REMOTE
The remote control buttons perform the same
functions as those on the control panel of the unit.
For best results, aim the remote directly at the
remote sensor on the front panel of the heater. The
remote has a 3 metre range of operation.
The remote control requires one "CR2025" type
battery. Remove the plastic tab from the battery and
battery terminal prior to first use of the remote
control.
MEMORY FUNCTION
Providing the unit is not switched off at the mains, the
memory function ensures the heater restarts in the
same mode as when last operated.
ECO MODE
LOW
H
EAT
/
H
IGH
H
EAT
PO
W
ER
BU
T
T
ON
OSC
ILLAT
ION
T
IM
ER
&
T
H
ER
M
OST
AT