background image

                                                                                                                               16 oz. Econo-16  

                                                                                                           

                 Models #2024, 2024ST 

7

 

Care and Cleaning 

 

 DANGER

 

Machine must be properly grounded to prevent electrical shock to personnel. 

DO NOT immerse in water. 

DO NOT clean appliance with a water jet.

 

Always unplug the equipment before cleaning or servicing. 

025_111616 

 

 

 

WARNING

 

To avoid serious burns, DO NOT touch the kettle while it is hot! 

028_082715 

 

Good sanitation practice demands that all food preparation equipment be cleaned regularly (only use non-
toxic, food grade cleaners). A clean looking, well-kept machine is one of the best ways of advertising your 
product. 
 

Note:

   It is extremely important to follow all cleaning procedures, otherwise parts damage and 

equipment failure will result. The warranty does not cover parts that are damaged due to 
improper cleaning. 

Daily Kettle Cleaning Instructions 

 

CAUTION:

 A hot kettle will cause burns if you touch it with your hand. Allow kettle to cool at least 1 

hour before attempting to clean. 

DO NOT

 use ice or water to cool down a hot kettle! 

Severe kettle damage will result! 

1.  When cool, wipe 

outside

 of kettle with a clean, soft cloth. 

DO NOT

 use oven cleaners or abrasive 

materials as they will damage the kettle. 

2.  Every night, mix Gold Medal’s Heat’n Kleen solution (Item No. 2095), 2 tablespoons per gallon of 

water. It is not necessary to use the entire gallon at once; only use enough to fill the kettle 1/2 
inch deep.  

3.  Turn kettle heat ON. When water starts to boil, turn kettle heat OFF.  

4.  Allow to cool at least 1 hour, then dump solution into a bucket and wipe inside of kettle with a 

clean cloth. Make sure all solution goes into the bucket; do not spill any in the interior of 
machine. 

For an extra dirty kettle, the process may be repeated; or, after turning kettle heat OFF, allow 
solution to sit in kettle overnight. The next morning, dump solution into a bucket and wipe inside 
of kettle with a clean cloth. 

5.  With unit OFF and unplugged, wipe kettle lead cord with a clean SLIGHTLY damp cloth. 

DO NOT 

get moisture into the kettle lead-in cord, severe damage will result.

 

 

Daily Unit Cleaning Instructions

 

 

1.  Turn machine OFF, unplug unit and allow it to cool before attempting to clean. 

2.  Clean all pans/accessories in order to sanitize them before each use. 

3.  Take a clean, SLIGHTLY damp cloth and wipe excess grease from glass and cabinet. 

Summary of Contents for Econo-16 2024






















Reviews: