Gold Medal 3015 Series Instruction Manual Download Page 11

X-15 Stainless Steel 

Whirlwind 

Model No. 3015 Series 

 

Page 11 

 

 

gmpopcorn.com 

 

FLOATER ADJUSTMENTS

 

In operation, the floss will collect on the FLOSS STABILIZER. If the floss collects “low” on the 

stabilizer, twist the front (leading) edge of the leather floaters down. You get more lift and the 

floss will collect higher. 
Form leather floaters as shown below. This creates a lifting action to float the floss higher on the 

outside wall of the floss pan.  

 

Shut Down Procedure 

When completing operation for the day (or any prolonged period), run all the sugar out of the 

floss head. When empty, turn the heat to highest position for approximately one minute to 

“clean” the band by baking off remaining sugar. 

NEVER

 put water in the floss head. 

Cleaning Instructions 

Unplug the machine and wait for the floss head to cool down to room temperature. Wipe all 

surfaces with a clean, damp cloth.  
Take pan and accessories to sink to clean with soap and water then rise and allow to dry. 

DO 

NOT use oven cleaners or abrasive materials 

as they will damage parts of machine.

 

Rotation 

Leather Floater 

Leading Edge of 

Leather Floaters 

seen twisted down 

Summary of Contents for 3015 Series


































Reviews: