manualshive.com logo in svg

Godex HD90, User Manual

Share
Download
Godex HD90 User Manual Download Page 9

Godex Label Printer User Guide 

 

 

  Page 9 

The Godex HD90 printer comes with the following materials: 

 

Quick Guide for unpacking, connecting, and loading paper into the printer. 

 

Products Guide CD 

 

USB cable (unused when you purchase the printer with wireless capability pre-installed) 

 

Power cable 

 

Power adapter 

 

Starter roll of 4” x 4” labels 

 

Thermal printer 

 

Wireless antenna 

Before you can configure the wireless LAN settings, you must connect the printer with a patch cable to your 
network. 

1.

 

Install the Control Center software package, as described on page 40. The Control Center software will 
enable you to configure the printer easily. 

2.

 

Remove all the packing tape from the thermal printer. 

3.

 

Make sure the printer power switch is in the off position. 

4.

 

Screw the wireless antenna into the antenna port on the lefthand side of the rear of the printer just 
above the power switch. 

5.

 

Plug the power adapter into the printer. 

6.

 

Plug the power cable into the outlet and connect it to the power adapter. 

7.

 

Plug a network cable into the RJ-45 port on the printer. 

8.

 

Plug the other end of the network cable into a networking port for your LAN. 

9.

 

By default the printer is set to use DHCP, so it should receive an IP address assignment from  your 
DHCP server. 

10.

 

If it is not already open, open the Control Center software. 

Summary of Contents for HD90









































Reviews:

No comments

Brands by name

Popular brands

Load more brands