Gocontrol GC-TBZ48 Installation & Operation Manual Download Page 13

Copyright 

©

 2015 Nortek Security & Control LLC     

11

Thermostat Setup Menus

The thermostat must be setup for the correct HVAC system type for proper opera  on.

Preset HVAC System se

ƫ

  ngs

The thermostat is preset for the following typical HVAC system con

fi

 gura  on:

•  HVAC system type: Standard gas/electric

•  HVAC fan type: Gas heat

• HVAC hea  ng stages: one

•  HVAC cooling stages: one

If the thermostat is installed on this type HVAC system, the System Setup does not need to be 
changed. 
If installed on a Heat Pump HVAC system or any HVAC con

fi

 gura  on other than the preset se   ngs, 

change the se   ngs in the SYSTEM setup menu to match the HVAC system.

NOTE:

 To conserve ba  ery life, the thermostat backlight turns o

  a  er a short   me of no ac  vity. 

The 

fi

 rst press of any bu   on turns on the backlight (but does not ini  ate any ac  on). Press the bu  on 

again to ini  ate the ac  on desired. If the backlight is already on, bu  on presses work with the 

fi

 rst 

press.

Wait Mode 

The thermostat has a Minimum O

  Time (MOT) delay a  er any hea  ng or cooling cycle ends. This 

delay prevents rapid hea  ng/cooling cycles and also provides “short cycle protec  on” for the system 
compressor. This delay may be no  ceable when you change a setpoint and it does not respond 
immediately due to the MOT delay   mer preven  ng the system from restar  ng. The MOT delay   me 
can be adjusted in the Advanced Se   ngs menu of the thermostat but there is a minimum of 

fi

 ve 

minutes delay to assure compressor protec  on.

Minimum Run Time (MRT)

The thermostat has a Minimum Run Time delay a  er the start of any hea  ng or cooling call. This 
minimum run   me assures even hea  ng and cooling cycles. The MRT will keep the system on, even 
if it reaches the setpoint room temperature, or you change the setpoint to a temperature that would 
sa  sfy the call, un  l the MRT expires. Changing the Mode to OFF will cancel the MRT and the system 
will turn o

   immediately. The MRT can be adjusted in the Advanced Se   ngs menu of the thermostat.

NOTE:

 The MRT delays are shown by 

fl

 ashing heat or cool icons on the display.

Summary of Contents for GC-TBZ48





























Reviews: