3
PACKING LIST
QTY
PARTS DESCRIPTION
6
¼” X ¾” HEX BOLTS
6
¼” FLAT WASHERS
6
¼” HEX NUTS
2
5/16” X 1” BUTTON HEAD BOLTS
2
5/16” FLAT WASHERS
2
5/16” LOCK NUTS
12
½” HEX NUTS
QTY
PARTS DESCRIPTION
24
½” FLAT WASHERS
12
½” X 1 1/2” HEX BOLTS
12
½” LOCK WASHERS
2
1602 LOWER BRACKETS
2
1604 LOWER BRACKETS
1
16014AA (D) DRIVER UPPER BRACKET
1
16014AA (P) PASSENGER UPPER BRACKET
2
1122LP LICENSE PLATE BRACKETS
INSTALLATION
STEP 1. READ THE INSTRUCTIONS COMPLETELY.
BEGINNING WITH THE DRIVER SIDE REMOVE THE (4) SCREWS AND 5MM HEX BOLT SECURING THE FRONT FASCIA
FILLER PANEL. FIG. #1
STEP 2. LOCATE AND REMOVE THE PLASTIC TOW HOOK COVER FROM THE LOWER BUMPER FASCIA. FIG. #2
I IF EQUIPPED, REMOVE THE BOLTS AND RECOVERY HOOK.
REPEAT THE ABOVE STEPS FOR THE PASSENGER SIDE.
STEP 3. LOCATE THE TWO HOLES IN THE LEFT SIDE OF THE DRIVER SIDE FRAME RAIL.
POSITION ONE OF THE 1602 LOWER MOUNTING BRACKETS UP TO THE FRAME, AND ATTACH THE BRACKET TO THE
SIDE OF THE FRAME USING TWO OF THE ½” X 1 ½” HEX BOLTS, FLAT WASHERS, LOCK WASHERS AND HEX NUTS.
FIG. #3 DO NOT TIGHTEN.
STEP 4. LOCATE THE SINGLE HOLE IN THE RIGHT SIDE OF THE DRIVER SIDE FRAME RAIL.
POSITION ONE OF THE 1604 LOWER MOUNTING BRACKETS UP TO THE FRAME, AND ATTACH THE BRACKET TO THE
FRAME AND TO THE 1602 BRACKET USING TWO OF THE ½” X 1 ½” HEX BOLTS, FLAT WASHERS, LOCK WASHERS
AND HEX NUTS. FIG. #4 DO NOT TIGHTEN.
STEP 5. LOCATE THE SINGLE HOLE IN THE RIGHT SIDE OF THE PASSENGER SIDE FRAME RAIL.
POSITION ONE OF THE 1602 LOWER MOUNTING BRACKETS UP TO THE FRAME, AND ATTACH THE BRACKET TO THE
FRAME USING ONE OF THE ½” X 1 ½” HEX BOLT, FLAT WASHERS, LOCK WASHER AND HEX NUT. DO NOT TIGHTEN.
STEP 6. LOCATE THE TWO HOLES IN THE LEFT SIDE OF THE PASSENGER SIDE FRAME RAIL. POSITION ONE OF
THE 1604 LOWER MOUNTING BRACKETS UP TO THE FRAME, AND ATTACH THE BRACKET TO THE FRAME AND TO
THE 1602 BRACKET USING THREE OF THE ½” X 1 ½” HEX BOLTS, FLAT W ASHERS, LOCK WASHERS AND HEX NUTS.
DO NOT SECURE.
STEP 7. ATTACH THE GRILLE GUARD ASSEMBLY TO THE OUTSIDE OF THE 1604 LOWER MOUNTING BRACKETS
USING THE 1/2” X 1 1/2” HEX BOLTS, FLAT WASHERS, LOCK WASHERS AND HEX NUTS. FIG. #5
DO NOT TIGHTEN
STEP 8. OPEN THE HOOD. LOCATE AND REMOVE THE SCREWS SECURING THE GRILLE TO THE RADIATOR
SHROUD.
STEP 9. ATTACH 16014AA (D) UPPER BRACKET TO THE RADIATOR SHROUD USING THE FACTOR SCREW AND TO THE
GRILLE GUARD SIDE PLATE USING THE 5/16” X 3/4” BUTTON HEAD BOLT, FLAT WASHER AND LOCK NUT. FIG. #6 &
FIG. #7 DO NOT TIGHTEN.
REPEAT THE ABOVE STEP FOR THE
PASSENGER SIDE BRACKET.
STEP 10. ALIGN THE GRILLE GUARD ASSEMBLY WITH THE FRONT OF THE VEHICLE AND TIGHTEN ALL MOUNTING
NUTS AND BOLTS. REATTACH THE FASCIA FILLER PANELS.
IF YOUR STATE LAW REQUIRES A FRONT LICENSE PLATE, ATTACH THE 1122LP BRACKETS, AND LICENSE PLATE TO
THE GRILLE GUARD CENTER PLATE USING THE ¼” HEX BOLTS, WASHERS AND NUTS. FIG. #8
3000 & 7000 SERIES STEPGUARD
COMPLETE GRILLE & BRUSH GUARD
INSTALLATION INSTRUCTIONS
PART NO. 3160M & 7160M 07-08 CHEVY 1500 AVALANCHE, TAHOE & SUBURBAN 2/4WD
Do not attempt to install this product on any vehicle other than the one it is designed for and listed above!
