manualshive.com logo in svg

GMP 90000, Operation And Maintenance

Share
Download
GMP 90000 Operation And Maintenance Download Page 22

Page 22 

 

General Machine Products (KT), LLC

 

 

 

Remove tension nut using a 13mm wrench

 

Loosen the belt tension screw

 

Remove the idler pulley

 

4.

 

Place the new belt in position on the drive pulley, place the idler pulley around the other end and re-

place the idler pulley onto the tensioning shaft. Replace the tension nut and then tension as described 

in section 8.4.

 

 

NOTE: NEVER POWER THE MACHINE UP OR RUN WITH THE GUARDS REMOVED. DOING SO MAY 

RESULT IN INJURY.

 

 

8.4 TENSIONING THE DRIVE BELTS

 

To tension the drive belts follow the steps below:

 

1.

 

Place belts in position as in section 8.3 and ensure belt is correctly located in all the pulley grooves.

 

2.

 

Tighten the tension screw with the tension nut slightly loose. This will begin to tighten the belt. Once the 

appropriate tension is reached, tighten the tension nut.

 

a. Note tightening the nut will tighten the belt slightly, please set the tension screw to compensate 

for this.

 

3.

 

Check the belt tension and adjust the tension as per above as required and check the tension nut is 

tight upon completion.

 

Summary of Contents for 90000





































Reviews:

No comments

Brands by name

Popular brands

Load more brands