GMC HD1400K Instruction Manual Download Page 10

10

Chuck replacement

Chuck removal
Always wear eye protection. 

Tighten the chuck around the shorter end of a hex key 

(not supplied) of 5mm or greater size. Using a wooden 

mallet or similar object, strike the longer end in the 

clockwise direction. This will loosen the screw inside the 

chuck.
1.  Open chuck jaws fully.
2.  Insert a phillips head screwdriver into front of chuck 

between jaws to engage screw head. 

Remove screw by turning clockwise. 

3.  Place the hex key in chuck and 

tighten. Using a wooden mallet or 

similar object, strike key sharply in 

the anti-clockwise direction. This 

will loosen the chuck so that it can 

be unscrewed by hand.

Chuck installation

1.  Screw the chuck on by 

hand as far as it will 

go and insert screw (LH 

thread).

2.  Tighten the chuck around 

the shorter end of a 

1/4”or large hex key 

(not supplied) strike the 

longer end in the clockwise direction with a wooden 

mallet.

3.  Remove the hex key and open the jaws fully. Tighten 

the screw in the centre of the chuck firmly.

Hints for use

Note.

 

When drilling into masonry the drilling rate is fast 

and burnout of the tip will occur if the drill bit is not 

constantly cleared. 

• 

Use only correctly sharpened drill bits, which are 

suitable for the material being drilled.

• 

To drill hard materials, firm pressure is required on 

the power tool. However, excessive pressure does not 

improve performance and places unnecessary pressure 

on the tool and its bit.

• 

When screw driving always use a pilot hole and set the 

speed dial to low. Press firmly on the screw head and 

pull the trigger gradually increasing the speed. It is 

always wiser to test the screw driving on a scrap piece 

of the same material you are using.

• 

Larger diameter holes in hard wood, steel and concrete 

have to be drilled at slower speeds. However, the motor 

must not be struggling with the operation. If the motor 

is struggling DO NOT continue working, pull the drill 

clear of the workpiece and run it on fast speed for a 

minute or so allowing the motor time to cool down 

before you continue with the task. If the job is too 

hard for the drill do not continue otherwise you could 

permanently damage the motor.

• 

Concrete drilling should be carried out on the highest 

speed.

DO NOT

 

overload motor when drilling concrete.

DO NOT

 

use too much pressure as the hammer action 

relies on the drill bit being able to move back and forward 

in the hole being drilled.
Always clear the flutes of the drill bit by removing it from 

the hole regularly.

Summary of Contents for HD1400K













Reviews: