background image

19

Troubleshooting cont.

DC circuit breaker 

continually tripping

1. Overload

1. Reduce load

2.  Faulty cords or equipment

 2.  Check for damaged, bare, or frayed wires on equipment. Replace.

3.  Incorrect cables used

3.  Check to make sure you are using the DC cables supplied with 

the actual generator. Using the incorrect cables could result in 

the crossing over of polarity. Only use the supplied DC cables 

with the actual generator.

4.  Mixed polarity  

4.  Check to make sure that the DC cables are connected to the 

correct battery polarity terminals. That is positive (+) to positive 

(+) and negative (-) to negative (-)

Generator 

overheating

1. Generator overloaded

1. Reduce load

2. Insufficient ventilation

2. Move to adequate supply of fresh air

Generator stops

1.  Generator may  

have fallen over

1.  Check to make sure that the generator is in it’s correct upright 

position. If not take corrective action to put it in the upright position

2.  Generator may  

have ran out of oil

2.  Check to make sure that the generator has oil in it. If not take 

corrective action to top up the oil tank

3.  Generator may have ran 

out of Fuel

3.  Check to make sure that the generator has fuel in it. If not take 

corrective action to top up the fuel tank

4.  Generator may not  

be correctly ventilated 

with free flowing air

4.  Check and make sure that the generator is located in a 

appropriately ventilated environment. If not relocate the 

generator to a well ventilated location.

5.  Generator fuel cap 

breather set on the 

closed position

5.  Check that the generator fuel cap has the breather located 

switch located on the “on” position, allowing air to mix with the 

fuel. If the breather cap is located in the “off” position rotate 

switch on the cap to the “on” position.

6.  Generator air filter  

may need cleaning

6.  Remove the air filter. Check to make sure that the air filter is 

clean. If required clean, dry and re-install the air filter. 

7.  Generator fuel filter  

may be blocked

7.  The internal in-line filter may be blocked. Contact your service 

agent for a service/replacement of the fuel filter.

Summary of Contents for G25

























Reviews: