manualshive.com logo in svg

Global 8550-RU, Operating Manual, Page: 23 / 61

Share
Download
Global 8550-RU Operating Manual Download Page 23

Global Power Technologies 

START-UP AND OPERATION 

302954 rev0 | Model 8550-RU  

Page 19 of 53 

4.1.4

 

AIR SHUTTER ADJUSTMENT 

After start-up, the air shutter will be in a fully opened position. The air shutter must be tuned for the 

site conditions to ensure optimal combustion. To test the air shutter during maintenance or service, 

start testing with the air shutter plate in a fully opened position. 
Refer to Figure 10 to identify the parts and follow the steps below to adjust the air shutter. 

NOTE:  The position of the cabinet door affects air intake. For these steps, open the cabinet door 

only to adjust the Air Shutter and keep the door closed as much as possible. 

 

 

1.

 

With the air shutter plate initially fully opened, 

close the cabinet door for at least 15 minutes 

then take a power reading and record it on the 

Start-Up Data Sheet.  

2.

 

Close the air shutter by 1/8 inch (3 mm) from its 

current position.  

3.

 

Close the cabinet door and wait 10 minutes for 

the TEG to stabilize.  

4.

 

Take a power reading and compare it to the 

previous reading. 

 

If the new power reading is higher than 

the previous reading, close the air shutter 

by another 1/8 inch (3 mm), wait 10 

minutes, and then take another power 

reading.  

Continue closing the air shutter by 1/8 

inch (3 mm) and checking the power every 

ten minutes until the power no longer 

rises, then proceed to the next step. 

 

If the new power reading is lower than the initial reading, open the Air Shutter by 1/8 inch 

(3 mm) past the initial setting, wait 10 minutes, then take another power reading. If this 

power reading is the same or lower than the previous reading, then the Air Shutter is 

correctly adjusted. Proceed to Step 7. 

NOTE:  If the Air Shutter reaches its fully open position, then leave the Air Shutter at this 

position and proceed to Step 7. 

 

 

 

If this reading is the same as the previous reading, proceed to the next step.

 

5.

 

Once the power reading has stabilized, open the Air Shutter by 1/4 inch (6 mm) from its current 

position. The Air Shutter is now optimally tuned for your ambient conditions and fuel supply. 

6.

 

Close the cabinet door and wait another 10 minutes for the TEG to stabilize.  

7.

 

Take a final power reading. 

Figure 10 – Air Shutter Adjustment

 

Summary of Contents for 8550-RU






























































Reviews:

No comments