background image

 

1

Wall Mounted Filtered Water Cooler

052120

globalindustrial.ca

User's manual

Manual del usuario

Manuel de l'utilisateur

Customer Service

US: 1-800-645-2986

Servicio de atención al Cliente

US: 1-800-645-2986

Service à la clientèle

Canada: 888-645-2986

        WARNING

  

 Keep compressor in upright position for 24 hours 

before water connections and initial power-on. Failure 

to do so will void warranty.

• For indoor commercial use only.

•  All installation work must be performed by authorized 

service personnel.

•  Two or more people are recommended to lift and install 

the unit.

•  To avoid the risk of property damage and/or personal 

injury, mount the unit to a flat finished wall surface with 

adequate support.

•  

Check local codes for plumbing requirements prior  

to installation.

•  Prior to initial installation, install a shut-off valve (not 

included) from the water supply.

•  Thoroughly flush all water lines and fittings of all foreign 

matter before connecting to the cooler. Failure to do so 

will void warranty.

• Check for any leaks before initial operation.

•  DO NOT attempt to repair or replace any part of your 

appliance unless it is specifically recommended in 

this manual. All other services should be referred to a 

qualified technician. 

• For use with clean, clear potable drinking water only.

•  Shut-off water supply during installation to reduce risk 

of water damage. 

•  

Ensure proper ventilation by allowing appropriate 

clearance of housing louvers to the wall on each side 

of the cooler, as specified in rough-in guide.

•  NEVER wire the compressor directly to an electrical supply.

• DO NOT allow children to play with the appliance.

•  Interior of unit may contain sharp edges. Wear gloves 

when handling or servicing unit.

•  Failure to follow installation instructions will void warranty.

Note:

 These fixtures are intended for indoor commercial 

use only. Do not expose to freezing temperatures. 

The grounding of electrical equipment to water lines is 

a common procedure. This grounding may be in the 

building or occur away from the building. This grounding 

can cause electric feedback into the water cooler 

creating an electrolysis which creates a metallic taste or 

causes the water metal content to increase. Connect to 

water supply using non-conductive materials.

Model 761217

Read this manual thoroughly prior to 

installation, operation or maintenance. 

Keep these instructions in a safe location 

for future reference. For questions, visit 

globalindustrial.com or contact Customer 

Service at 1-800-645-2982.

Summary of Contents for 761217











Reviews: