CONSUMER: Contact your installer.
INSTALLER: CALL BEFORE DIGGING UP OR UNINSTALLING
DISTRIBUTOR
1) as phone number.
9. INTEGRATOR DIP SWITCHES
Dip switches control sounder and repeater mode on Integrator.
SOUNDER
Turn dip switch 1 ON to turn sounder on.
REPEATER MODE
Turn dip switch 2 ON to turn Integrator into a repeater. In repeater mode,
the Integrator installed in the home (see #11 below). Red and blue LED will
10. INSTALLING INTEGRATOR
11. REPEATER MODE
To increase radio range, it may be necessary to make the Integrator a repeater.
If the signal from sensor puck is not reaching the Integrator:
1. Move the sensor closer to the Integrator, and/or
2. Install a repeater in the home between the sensor puck and Integrator
2. Remove enclosure cover by carefully pushing side tabs in.
3. Connect power supply to terminals 1 & 2 (no polarity).
4. Turn dip switch 2 ON (see #9 above). This puts the unit in repeater
mode. The red and blue LEDs will alternately blink to indicate repeater mode. It
the Integrator installed beside the main system.
5. Install repeater in a window closest to the sensor puck.
NOTE: To order repeater kit, use product code CW-REP.
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
uses and can radiate radio frequency energy and, if not installed and used in accordance with
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed
and operated with minimum distance between 20cm the radiator your body: Use only the
supplied antenna.
This device complies with Industry Canada licence-exempt RSS
interference; (2) this device must accept any interference, including interference that may cause
This Class [B] digital apparatus complies with Canadian ICE-003.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
est de 20 cm.
The device has been evaluated portable device RF exposure requirements. The device is kept
at least 5 mm away from the user’s body.
TO LOW
BATTERY
INPUTS
IF N.O.
TO LOW
BATTERY
INPUTS
IF N.C.
TO ZONE
INPUTS or
WIRELESS
SWITCH
IF N.O.
TO ZONE
INPUTS or
WIRELESS
SWITCH
IF N.C.
POWER +
POWER -
LOW BATTERY
N.C.
N.O.
COM
ALARM RELAY
N.O.
COM
N.C.
(No Polarity)
POWER
DO NOT USE
TO EXIT
TERMINALS
IF N.O.
TO EXIT
TEMINALS
IF N.C.
POWER +
POWER -
N.C.
N.O.
COM
LOW BATTERY
N.O.
COM
N.C.
ALARM
(No Polarity)
POWER
DUAL EXITTERMINAL
Your system integrates seamlessly with any security/H.A. system or electric
gate operator.
NOTE: DO NOT USE WITH SOLAR GATES.
DO NOT USE
TO “EXIT”
or “OPEN”
TERMINAL
TO “GND”
or “COM”
(use one)
POWER +
N.C.
N.O.
COM
LOW BATTERY
N.O.
COM
N.C.
ALARM
(No Polarity)
POWER
SINGLE EXIT TERMINAL
Technical Speci
fi
cations
Sensor “Puck”
Integrator
Power Required
2 - CR123A batteries (6 V)
8-24VAC; 8-28VDC
Stand-By Current
22 Microamps (μA)
25 Milliamps (mA)
Alarm Current
130 Milliamps (mA)
40-80 Milliamps (mA)
Relay Time
2 seconds
Relay Contacts
SPDT, N.O. or N.C. (Form C)
Relay Contact
Rating
2 amp/24 VDC (1 mA at
5 VDC min. load)
Radio Range
Tested above ground, no obstructions, up to 2,500 ft.
*
Tested flush with ground, no obstructions, up to 1,000 ft.
*
Use optional Repeater (CW-REP) to increase radio range
Battery Life
1-3 years
*
Enclosure Rating
IP68
Strength Rating
9.39 ton-force (8514 kgf)
–
Temperature Range
-25° F. +140° F.
(-32° C. 60° C.)
Dimensions
4.5
"
dia. x 2.5
"
H
(11.43 cm x 6.35 cm)
3.25
"
L x 2
"
H x .875
"
D
(8.25 cm x 5.08 cm x 2.22 cm)
Weight
2 lbs. (.90 kg)
1 lb. (.45 kg)
*
Integrator uses 8-24 VAC or 8-30
VDC. Use security/H.A. system or
gate operator to power or use any
12VDC power supply.
WA
RRANTY
W
A
RR
AN
TY
WA
RR
A
N
TY
Y
E
A
R
14. FIVE YEAR WARRANTY
13. RETURNING MERCHANDISE
12. OPTIONAL EXTERNAL GATE ANTENNA
sealed
metal gate
operator that blocks the RF signal. If that is the case, use the included coaxial
cable and install antenna externally, per the following:
1.
Drill 1/4”
hole in gate
operator.
2.
Put female end of cable
through hole and use nut to
sure rubber gasket stays on
outside between operator
and washer.
3.
Screw antenna on male
end of cable outside operator.
WARNING: DO NOT SHIP BATTERIES WHEN RETURNING PRODUCT TO SUPPLIER.
NOTE: DIP SWITCH
COLOR MAY VARY
#1 Sounder
mode ON
#2 Repeater
mode ON
2.
th
e
4.
Screw male end of cable to
Integrator antenna connector.
WARNING: This product can expose
you to chemicals including Acrylonitrile,
which is know to the State of California
to cause cancer. For more information,
go to www.P65Warnings.ca.gov.
AUTOMATIC GATE OPERATORS
15. FCC WARNING
SECURITY/HOME AUTO SYSTEMS
YOU MUST ADD A SAFETY TO GATE
WHEN USING CW-SYS FOR FREE EXIT.
E3957
AUSTRALIA
FCC ID #: 2AUXCCWIN & 2AUXCCWSN (U.S.)
IC#: 25651-CWIN & 25651-CWSN (Canada)
www.global-access.com.au
1300 366 046
